HT82K95EE datasheet(18/45 Pages) HOLTEK

18 / 45 page

HT82K95EE/HT82K95AE

Rev. 1.20

August 28, 2006

Data EEPROM Functional Description

· Serial clock (SCL)

The SCL input is used for positive edge clock data into

each EEPROM device and negative edge clock data

out of each device.

· Serial data (SDA)

The SDA pin is bidirectional for serial data transfer.

The pin is open-drain driven and may be wired-OR

with any number of other open-drain or open collector

devices.

Memory Organization

· 1K Serial EEPROM

Internally organized with 128 8-bit words, the 1K re-

quires an 8-bit data word address for random word ad-

dressing.

Device Operations

· Clock and data transition

Data transfer may be initiated only when the bus is not

busy. During data transfer, the data line must remain

stable whenever the clock line is high. Changes in

data line while the clock line is high will be interpreted

as a START or STOP condition.

· Start condition

A high-to-low transition of SDA with SCL high is a start

condition which must precede any other command

(refer to Start and Stop Definition Timing diagram).

· Stop condition

A low-to-high transition of SDA with SCL high is a stop

condition. After a read sequence, the stop command

will place the EEPROM in a standby power mode (re-

fer to Start and Stop Definition Timing Diagram).

· Acknowledge

All addresses and data words are serially transmitted

to and from the EEPROM in 8-bit words. The

EEPROM sends a zero to acknowledge that it has re-

ceived each word. This happens during the ninth

clock cycle.

Device Addressing

The 1K EEPROM devices all require an 8-bit device ad-

dress word following a start condition to enable the chip

for a read or write operation. The device address word

consist of a mandatory one, zero sequence for the first

four most significant bits (refer to the diagram showing

the Device Address). This is common to all the

EEPROM device.

The next three bits are the fixed to be

²0².

The 8th bit of device address is the read/write operation

select bit. A read operation is initiated if this bit is high

and a write operation is initiated if this bit is low.

If the comparison of the device address succeed the

EEPROM will output a zero at ACK bit. If not, the chip will

return to a standby state.

Write Operations

· Byte write

A write operation requires an 8-bit data word address

following the device address word and acknowledg-

ment. Upon receipt of this address, the EEPROM will

again respond with a zero and then clock in the first

8-bit data word. After receiving the 8-bit data word, the

EEPROM will output a zero and the addressing de-

vice, such as a microcontroller, must terminate the

write sequence with a stop condition. At this time the

EEPROM enters an internally-timed write cycle to the

non-volatile memory. All inputs are disabled during

this write cycle and EEPROM will not respond until the

write is completed (refer to Byte write timing).

· Acknowledge polling

To maximise bus throughput, one technique is to allow

the master to poll for an acknowledge signal after the

start condition and the control byte for a write com-

mand have been sent. If the device is still busy imple-

menting its write cycle, then no ACK will be returned.

The master can send the next read/write command

when the ACK signal has finally been received.

S C L

S D A

D a t a a l l o w e d

t o c h a n g e

A d d r e s s o r

a c k n o w l e d g e

v a l i d

S t o p

c o n d i t i o n

S t a r t

c o n d i t i o n

N o A C K

s t a t e

R / W

D e v i c e A d d r e s s

R / W

D e v i c e a d d r e s s

W o r d a d d r e s s

D A T A

A C K

S t o p

S t a r t

S D A

A C K

Byte Write Timing

HT82K95EE Datasheet(PDF) 18 Page - Holtek Semiconductor Inc

HT82K95EE Datasheet(HTML) 18 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45

Datasheet Download

Link URL