Electronic Components Datasheet Search
  English  ▼

X  

AD5778R Datasheet(PDF) 21 Page - Analog Devices

Part # AD5778R
Description  2-Channel, 300 mA Current Source Output 16-Bit SoftSpan DAC
PDF  26 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

AD5778R Datasheet(HTML) 21 Page - Analog Devices

Back Button AD5778R Datasheet HTML 17Page - Analog Devices AD5778R Datasheet HTML 18Page - Analog Devices AD5778R Datasheet HTML 19Page - Analog Devices AD5778R Datasheet HTML 20Page - Analog Devices AD5778R Datasheet HTML 21Page - Analog Devices AD5778R Datasheet HTML 22Page - Analog Devices AD5778R Datasheet HTML 23Page - Analog Devices AD5778R Datasheet HTML 24Page - Analog Devices AD5778R Datasheet HTML 25Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 21 / 26 page
background image
Data Sheet
AD5778R
THEORY OF OPERATION
analog.com
Rev. 0 | 21 of 26
Table 11. Fault Register (Continued)
FR
Bit
Fault Condition
FR4
Invalid SPI sequence length. Valid sequence lengths are 24, 32, and
multiples of 32 bits. For all other lengths, FR4 is set, and the SPI instruction
is ignored.
Fault Indicator Pin (FAULT)
The FAULT pin is an open-drain N-channel output that pulls low
when a fault condition is detected. The FAULT pin is released
on the next rising CS/LD edge. The pin is an open-drain output
suitable for wired-OR connection to an interrupt bus, but a pull-up
resistor on the bus is required.
Fault Conditions and Thermal Overload
Protection
There are four types of fault conditions that cause the FAULT pin to
pull low. First, the FR0 and FR1 flag an open-circuit (OC) condition
on any of the output pins (OUT0 and OUT1, respectively) when an
output channel enters dropout due to insufficient voltage from VDDx
to OUTx. Independent open-circuit detection is provided for each of
the two DAC current output pins.
The FR2 bit provides a detection flag that is set when the die
temperature exceeds 175°C. The overtemperature condition also
forces both DAC channels to power down and the open-drain
FAULT pin to pull low. The FR3 bit remains set, and the device
stays in shutdown until the die cools. Below approximately 150°C,
the DAC channels can be returned to normal operation. Note that
a CS/LD rising edge releases the FAULT pin regardless of the die
temperature.
Because any DAC channel can source up to 300 mA, die heating
potential of the system design should be evaluated carefully. The
FR4 bit, a power-limit protection flag, is provided to help prevent
accidental damage to the current output device(s). The power-limit
fault condition is triggered for the 200 mA and 300 mA full-scale
current spans when the voltage difference between an output
supply pin (VDDx) and its current output pin (OUTx) is ≥ 10 V.
Finally, the FR4 bit is provided to flag invalid SPI word lengths.
Valid word lengths are 24 bits, 32 bits, and integer multiples of 32
bits. Any other length causes the FR4 flag to set, the FAULT pin to
assert, and the instruction itself to be ignored.
CONFIG COMMAND
The CONFIG command has four arguments—open circuit detection
disable (OC), power limit protection disable (PL), thermal shutdown
disable (TS), and reference disable (RD) (see Figure 30).
Setting the OC bit disables the open-circuit detection (FR0 and
FR1). Likewise, the PL bit disables power-limit protection (FR3),
and the TS bit disables thermal protection (FR2). Use these options
with caution, particularly the PL bit and the TS bit.
The RD bit is used to select the external-reference operation.
The REFCOMP pin must be grounded for external reference use
whether the RD bit is set or not.
Figure 30. CONFIG Command Syntax: OC, PL, TS, and RD



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com