| Electronic Components Datasheet Search |
|
INA333 Datasheet(PDF) 15 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
INA333 Datasheet(HTML) 15 Page - Texas Instruments |
|
15 / 35 page ![]() 15 INA333 www.ti.com SBOS445C – JULY 2008 – REVISED DECEMBER 2015 Product Folder Links: INA333 Submit Documentation Feedback Copyright © 2008–2015, Texas Instruments Incorporated Typical Application (continued) 8.2.1 Design Requirements The device can be configured to monitor the input differential voltage when the gain of the input signal is set by the external resistor RG. The output signal references to the Ref pin. The most common application is where the output is referenced to ground when no input signal is present by connecting the Ref pin to ground. When the input signal increases, the output voltage at the OUT pin increases, too. 8.2.2 Detailed Design Procedure 8.2.2.1 Setting the Gain Gain of the INA333 device is set by a single external resistor, RG, connected between pins 1 and 8. The value of RG is selected according to Equation 1: G = 1 + (100 k Ω / RG) (1) Table 1 lists several commonly-used gains and resistor values. The 100 k Ω in Equation 1 comes from the sum of the two internal feedback resistors of A1 and A2. These on-chip resistors are laser trimmed to accurate absolute values. The accuracy and temperature coefficient of these resistors are included in the gain accuracy and drift specifications of the INA333 device. The stability and temperature drift of the external gain setting resistor, RG, also affects gain. The contribution of RG to gain accuracy and drift can be directly inferred from the gain Equation 1. Low resistor values required for high gain can make wiring resistance important. Sockets add to the wiring resistance and contribute additional gain error (possibly an unstable gain error) in gains of approximately 100 or greater. To ensure stability, avoid parasitic capacitance of more than a few picofarads at the RG connections. Careful matching of any parasitics on both RG pins maintains optimal CMRR over frequency. (1) NC denotes no connection. When using the SPICE model, the simulation will not converge unless a resistor is connected to the RG pins; use a very large resistor value. Table 1. Commonly-Used Gains and Resistor Values DESIRED GAIN RG (Ω) NEAREST 1% RG (Ω) 1 NC(1) NC 2 100k 100k 5 25k 24.9k 10 11.1k 11k 20 5.26k 5.23k 50 2.04k 2.05 100 1.01k 1k 200 502.5 499 500 200.4 200 1000 100.1 100 8.2.2.2 Internal Offset Correction The INA333 device internal operational amplifiers use an auto-calibration technique with a time-continuous 350- kHz operational amplifier in the signal path. The amplifier is zero-corrected every 8 μs using a proprietary technique. Upon power-up, the amplifier requires approximately 100 μs to achieve specified VOS accuracy. This design has no aliasing or flicker noise. 8.2.2.3 Offset Trimming Most applications require no external offset adjustment; however, if necessary, adjustments can be made by applying a voltage to the REF pin. Figure 33 shows an optional circuit for trimming the output offset voltage. The voltage applied to REF pin is summed at the output. The operational amplifier buffer provides low impedance at the REF pin to preserve good common-mode rejection. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |