| Electronic Components Datasheet Search |
|
MSU2052C40 Datasheet(PDF) 5 Page - Mosel Vitelic, Corp |
|
|
|||||||||||||||||||||||||||||
MSU2052C40 Datasheet(HTML) 5 Page - Mosel Vitelic, Corp |
|
5 / 21 page ![]() 5 Rev. 1.0 February 1998 MOSEL VITELIC MSU2052/U2032 Pin Descriptions Vss Circuit ground potential. VDD +3V (or +5 V) power supply during operation. PORT 0 Port 0 is an 8-bit open drain bidirectional I/O port. It is also the multiplexed low-order address and data bus when using external memory. It also contains the timer 2 & its control pins. PORT 1 Port 1 is an 8-bit quasi-bidirectional I/O port with internal pull-up resistance. PORT 2 Port 2 is an 8-bit quasi-bidirectional I/O port with internal pull-up resistance. It also emit the high-order address byte when accessing external memory. PORT 3 Port 3 is an 8-bit quasi-bidirectinal I/O port with internal pull-up resistance. It also contains the interrupt, timer, serial port and #RD as well as #WR pins that are used by various options. The output latch corresponding to a secondary function must be programmed to one (1) for that function to operate. The secondary functions are assigned to the pins of port 3, as follows: - RXD/data (P3.0). Serial port's transmitter data output (asynchronous) or data input/output (asynchronous). - TXD/clock (P3.1). Serial port's transmitter data output (asynchronous) or data output (asynchronous). - #INT0 (P3.2). Interrupt 0 input or gate control input for counter 0. - #INT1 (P3.3). Interrupt 1 input or gate control input for counter 1. - T0 (P3.4). Input to counter 0. - T1 (P3.4). Input to counter 1. - #WR (P3.6). The write control signal latches the data byte from Port 0 into the External Data Memory. - #RD (P3.7). The read control signal enables External Data Memory to Port 0. RES A high on this pin for two machine cycles (24 clocks) while the oscillator is running, resets the device. The data in RAM is preserved when reset signals - reset does not clear the data in RAM. ALE Provides Address Latch Enable output used for latching the address into external memory during normal operation. #PSEN The Program Store Enable output is a control signal that enables the external Program Memory to the bus during normal fetch operations. #EA When held at a TTL high level, the MSU2052 executes instructions from the internal ROM when the PC is less than 4096. When held at a TTL low level, the MSU2052 fetches all instuctions from external Program Memory. XTAL 1 Input to the oscillator's high gain amplifier. A crystal or external source can be used. XTAL 2 Output from the oscillator's amplifier. Required when a crystal is used. Terms Idle Mode During idle mode, the CPU is stopped but below blocks are kept functioning: clock generator, RAM, timer/ counters, serial port and interrupt block. To save power consumption, user's software program can invoke this mode. The on-chip data RAM retains the values during this mode, but the processor stops executing instructions. In Idle mode (IDL=1), the oscillator continues to run and the interrput, and timer blocks continue to be clocked but the clock signal is gated off to the CPU. The activities of the CPU no longer exist unless waiting for an interrupt request. -An instruction that sets flag (PCON.0) causes that to be the last instruction executed before going into the Idle Mode. -In the Idle Mode, the internal clock signal is gated off to the CPU, but not to the interrupt, Timer function. -The CPU status is entirely preserved in its: the Stack Pointer, Program Counter, Program Status Word, Accumulator, and all other registers maintain their data during Idle mode. -There are three ways to terminate the Idle Mode. 1) By interrupt Activation of any enabled interrupt will cause flag (PCON.0) to be cleared by hardware, termination the Idle Mode. After the program wakes up, the PC value will point as interrupt vector (if enable IE register) and execute interrupt service routine then return to PC+1 address after the program wakes up. 2) By hardware reset Since the clock oscillator is still running, the hardware reset needs to be held active for only two machine cycles (24 oscillator periods) to complete the reset. All SFR and PC value will be cleared to reset value. 3) By one of CLK, DATA, PORT 2.0-2.7 transition to low (falling edge trigger) After the program wakes up, the PC value will be 0023h (if enable IE register) and execute interrupt service routine and then returns to PC+1 address after the program wakes up. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |