| Electronic Components Datasheet Search |
|
LTC2928IG Datasheet(PDF) 5 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LTC2928IG Datasheet(HTML) 5 Page - Linear Technology |
|
5 / 32 page ![]() LTC2928 5 2928f SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS External Voltage Reference Pin: REF VREF Reference Voltage Output 100% Sequence Threshold 67% Sequence Threshold 33% Sequence Threshold 10% Sequence Threshold IREF = 0.2mA, –1mA, CREF = ≤ 1000pF VSEL = VCC VSEL = VCC VSEL = VCC VSEL = VCC ● ● ● ● ● 1.172 1.172 0.780 0.386 0.109 1.189 1.189 0.793 0.396 0.119 1.205 1.205 0.806 0.406 0.129 V V V V V Over Voltage Indication Pin: OV VOV(OL) OV Voltage Output Low IOV = 2.5mA ● 0.15 0.3 V VOV(OH) OV Voltage Output High (Note 7) IOV = –1μA ● VCC – 1 V tOV OV Indication Time (Note 8) OV Low Time Upon Cleared OV Event, CRTMR = 1500pF ● 5 6 7 ms Over Voltage Adjust Pin: OVA VOVA(TH) Over Voltage Threshold at Comparator Inputs (Note 9) VOVA = GND VOVA Floating VOVA = VCC = 3.3V ● ● ● 0.546 0.650 1.042 0.556 0.660 1.072 0.566 0.670 1.102 V V V Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All currents into pins are positive, all voltages are referenced to GND unless otherwise noted. Note 3: Internal circuits regulate the EN output voltage to VEN. Driving this pin to voltages beyond VEN may damage the part. Note 4: The comparator outputs have internal pull-ups to VCC of typically –10μA. However, external pull-up resistors may be used when faster rise times are required or for VOH voltages greater than VCC. ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C, VCC = 3.3V unless otherwise noted. Note 5: The CAS high time after an ON edge is stretched by the ON pin propagation delay (20μs typical). Note 6: The DONE pull-down current is present when DONE is high to facilitate cascading multiple LTC2928s. Note 7: The RST and OV outputs have an internal pullup to VCC of typically –10μA. However, external pull-up resistors may be used when faster rise times are required or for VOH voltages greater than VCC. Note 8: If the termination of under and overvoltage events occur within one nominal tRTMR period, the variation in tRTMR and/or tOV may be ±15%. Note 9: Use a resistor from OVA to ground or VCC to configure overvoltage thresholds within the max/min ranges shown. See Applications Information for details. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |