| Electronic Components Datasheet Search |
|
SE98ATP Datasheet(PDF) 9 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
SE98ATP Datasheet(HTML) 9 Page - NXP Semiconductors |
|
9 / 43 page ![]() SE98A_2 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 02 — 6 August 2009 9 of 43 NXP Semiconductors SE98A DDR memory module temp sensor, 1.7 V to 3.6 V 7.3.2.2 Critical trip The Tth(crit) temperature setting is programmed in the Critical Alarm Trip register (04h) as modified by hysteresis as programmed in the Configuration register. When the temperature reaches the critical temperature value in this register (and EVENT is enabled), the EVENT output asserts and cannot be de-asserted until the temperature drops below the critical temperature threshold. The EVENT cannot be cleared through the Clear EVENT bit (CEVNT) or SMBus ALERT. The Critical Alarm Trip should always be set above the Upper Boundary Alarm Trip. • Advisory notification: – NXP device: Requires one conversion cycle (125 ms) after setting the Alarm Window before comparing the alarm limit with temperature register to ensure that there is correct data in the temperature register before comparing with the Alarm Window and operating EVENT output. – Competitor devices: Compares the Alarm Window with temperature register at any time, so they get the EVENT output immediately when new Tth(crit) and EVENT output are set at the same time. – Work-around: Wait at least 125 ms before enabling EVENT output (EOCTL = 1). Intel will change Nehalem BIOS so that Tth(crit) is set for more than 125 ms before EVENT output is enabled and Event value is checked. 1. Set Tth(crit). 2. Doing something else (make sure that exceeds 125 ms). 3. Enable the EVENT output (EOCTL = 1). 4. Wait 20 µs. 5. Read Event value. – SE98B will compare Alarm Window and temperature register immediately after setting. 7.3.3 Event operation modes 7.3.3.1 Comparator mode In comparator mode, the EVENT output behaves like a window-comparator output that asserts when the temperature is outside the window (e.g., above the value programmed in the Upper Boundary Alarm Trip register or below the value programmed in the Lower Boundary Alarm Trip register or above the Critical Alarm Trip resister if Tth(crit) only is selected). Reads/writes on the registers do not affect the EVENT output in comparator mode. The EVENT signal remains asserted until the temperature goes inside the alarm window or the window thresholds are reprogrammed so that the current temperature is within the alarm window. The comparator mode is useful for thermostat-type applications, such as turning on a cooling fan or triggering a system shutdown when the temperature exceeds a safe operating range. 7.3.3.2 Interrupt mode In interrupt mode, EVENT asserts whenever the temperature crosses an alarm window threshold. After such an event occurs, writing a 1 to the Clear EVENT bit in the configuration register de-asserts the EVENT output until the next trigger condition occurs. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |