| Electronic Components Datasheet Search |
|
PCA9558PW Datasheet(PDF) 7 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
PCA9558PW Datasheet(HTML) 7 Page - NXP Semiconductors |
|
7 / 27 page ![]() PCA9558_4 © NXP B.V. 2009. All rights reserved. Product data sheet Rev. 04 — 14 April 2009 7 of 27 NXP Semiconductors PCA9558 8-bit I2C-bus/SMBus I/O port The Multiplexer function controls the six open-drain outputs, MUX_OUTx and NON_MUXED_OUT. This control is affected by the input pins MUX_SELECT (pin 19), MUX_OUT_LOW (pin 26), and/or an internal register programmed via the I2C-bus. Upon power-up, the multiplex function is controlled by the MUX_SELECT and MUX_OUT_LOW pins. When the MUX_SELECT signal is a logic 0, the multiplexer will select the data from the 6-bit EEPROM to drive on the MUX_OUTx and NON_MUXED_OUT pins. When the MUX_SELECT signal is a logic 1, the multiplexer will select the MUX_INx pins to drive on the MUX_OUTx pins. The NON_MUXED_OUT output is latched from the 6-bit EEPROM on a rising edge of the MUX_SELECT signal. This latch is transparent while the MUX_SELECT signal is a logic 0. An internal control register, written via the I2C-bus, can also control the multiplexer function. When this register is written, the MUX_SELECT function can change from the external pin to an internal register. In this register a bit will act in a similar fashion to the MUX_SELECT input, i.e., a logic 1 will cause the multiplexer to select data from the 6-bit EEPROM to drive on the MUX_OUTx and NON_MUXED_OUT pins. In this configuration, the NON_MUXED_OUT will latch data when the PCA9558 acknowledges the I2C-bus. The MUX_SELECT pin will have no effect on the MUX_OUTx or NON_MUXED_OUT while in this mode. When the MUX_OUT_LOW signal is a logic 0 and the multiplexer is configured so that the MUX_OUTx pins are being driven by the 6-bit EEPROM, the MUX_OUTx pins will be driven to a logic 0. This information is summarized in Table 4. [1] These are the 2 LSBs of the MUX Control (MUXCNTRL) register. [2] NON_MUXED_OUT value will be the value present in the 6-bit EEPROM at the time of the rising edge of the MUX_SELECT input. [3] NON_MUXED_OUT value will be the value present in the 6-bit EEPROM at the time of the slave ACK when bit 1 has changed from logic 0 to logic 1. If the MUX_OUTx outputs are being driven by the 6-bit EEPROM and this EEPROM is programmed, the outputs will remain stable and change to the new values after the EEPROM program cycle completes. Examples of read/write for MUX control can be found in Figure 7. Table 4. Multiplexer function table Register Input Output B1[1] B0[1] MUX_OUT_LOW MUX_SELECT MUX_OUTx NON_MUXED_OUT x 0 0 1 MUX_INx inputs latched from EEPROM[2] x0 0 0 0 0 x 0 1 1 MUX_INx inputs latched from EEPROM[2] x 0 1 0 from EEPROM from EEPROM 0 1 0 x MUX_INx inputs latched from EEPROM[3] 110 x 0 0 0 1 1 x MUX_INx inputs latched from EEPROM[3] 1 1 1 x from EEPROM from EEPROM |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |