Electronic Components Datasheet Search
  English  ▼

X  

DS87C550 Datasheet(PDF) 35 Page - Dallas Semiconductor

Part # DS87C550
Description  EPROM High-Speed Micro with A/D and PWM
PDF  50 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  DALLAS [Dallas Semiconductor]
Direct Link  https://www.maximintegrated.com/en.html
Logo DALLAS - Dallas Semiconductor

DS87C550 Datasheet(HTML) 35 Page - Dallas Semiconductor

Back Button DS87C550 Datasheet HTML 31Page - Dallas Semiconductor DS87C550 Datasheet HTML 32Page - Dallas Semiconductor DS87C550 Datasheet HTML 33Page - Dallas Semiconductor DS87C550 Datasheet HTML 34Page - Dallas Semiconductor DS87C550 Datasheet HTML 35Page - Dallas Semiconductor DS87C550 Datasheet HTML 36Page - Dallas Semiconductor DS87C550 Datasheet HTML 37Page - Dallas Semiconductor DS87C550 Datasheet HTML 38Page - Dallas Semiconductor DS87C550 Datasheet HTML 39Page - Dallas Semiconductor Next Button
Zoom Inzoom in Zoom Outzoom out
 35 / 50 page
background image
DS87C550
35 of 50
DC ELECTRICAL CHARACTERISTICS
Input Leakage Port 0, Bus
Mode
IL
-300
+300
µA
9
RST Pulldown Resistance
RRST
50
170
kO
NOTES FOR DS87C550 DC ELECTRICAL CHARACTERISTICS:
All parameters apply to both commercial and industrial temperature operation unless otherwise noted.
1. Voltage referenced to digital ground (GND).
2. Active current measured with 33 MHz clock source on XTAL1, VCC=RST=5.5V, other pins
disconnected.
3. Idle mode current measured with 33 MHz clock source on XTAL1, VCC=5.5V, RST at ground, other
pins disconnected.
4. Stop mode current measured with XTAL1 and RST grounded, VCC=5.5V, all other pins disconnected.
This value is not guaranteed. Users that are sensitive to this specification should contact Dallas
Semiconductor for more information.
5. When addressing external memory.
6. RST=VCC. This condition mimics operation of pins in I/O mode. Port 0 is tristated in reset and when
at a logic high state during I/O mode.
7. During a 0 to 1 transition, a one-shot drives the ports hard for two oscillator clock cycles. This
measurement reflects port in transition mode.
8. Ports 1, 2, 3, 5, 6 source transition current when being pulled down externally. Current reaches its
maximum at approximately 2V.
9. 0.45<Vin<V CC. Not a high impedance input. This port is a weak address holding latch in Bus Mode.
Peak current occurs near the input transition point of the latch, approximately 2V.
10. 0.45<Vin<V CC. RST=VCC. This condition mimics operation of pins in I/O mode.
11. This is the current required from an external circuit to hold a logic low level on an I/O pin while the
corresponding port latch is set to 1. This is only the current required to hold the low level; transitions
from 1 to 0 on an I/O pin will also have to overcome the transition current.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com