AT90PWM2 datasheet(180/365 Pages) ATMEL

180 / 365 page

180

4317K–AVR–03/2013

AT90PWM2/3/2B/3B

means that it will not receive incoming data. Note that the SPI logic will be reset once the SS pin

is driven high.

The SS pin is useful for packet/byte synchronization to keep the slave bit counter synchronous

with the master clock generator. When the SS pin is driven high, the SPI slave will immediately

reset the send and receive logic, and drop any partially received data in the Shift Register.

17.2.2

Master Mode

When the SPI is configured as a Master (MSTR in SPCR is set), the user can determine the

direction of the SS pin.

If SS is configured as an output, the pin is a general output pin which does not affect the SPI

system. Typically, the pin will be driving the SS pin of the SPI Slave.

If SS is configured as an input, it must be held high to ensure Master SPI operation. If the SS pin

is driven low by peripheral circuitry when the SPI is configured as a Master with the SS pin

defined as an input, the SPI system interprets this as another master selecting the SPI as a

slave and starting to send data to it. To avoid bus contention, the SPI system takes the following

actions:

The MSTR bit in SPCR is cleared and the SPI system becomes a Slave. As a result of

the SPI becoming a Slave, the MOSI and SCK pins become inputs.

The SPIF flag in SPSR is set, and if the SPI interrupt is enabled, and the I-bit in SREG is

set, the interrupt routine will be executed.

Thus, when interrupt-driven SPI transmission is used in Master mode, and there exists a possi-

bility that SS is driven low, the interrupt should always check that the MSTR bit is still set. If the

MSTR bit has been cleared by a slave select, it must be set by the user to re-enable SPI Master

mode.

17.2.3

MCU Control Register – MCUCR

• Bit 7– SPIPS: SPI Pin Redirection

Thanks to SPIPS (SPI Pin Select) in MCUCR Sfr, SPI pins can be redirected.

On 32 pins packages, SPIPS has the following action:

–

When the SPIPS bit is written to zero, the SPI signals are directed on pins

MISO,MOSI, SCK and SS.

–

When the SPIPS bit is written to one,the SPI signals are directed on alternate SPI

pins, MISO_A, MOSI_A, SCK_A and SS_A.

On 24 pins package, SPIPS has the following action:

–

When the SPIPS bit is written to zero, the SPI signals are directed on alternate SPI

pins, MISO_A, MOSI_A, SCK_A and SS_A.

–

When the SPIPS bit is written to one,the SPI signals are directed on pins

MISO,MOSI, SCK and SS.

Note that programming port are always located on alternate SPI port.

Bit

6543

210

SPIPS

–

PUD

–

IVSEL

IVCE

MCUCR

Read/Write

R/W

Initial Value

0000

000

AT90PWM2 Datasheet(PDF) 180 Page - ATMEL Corporation

AT90PWM2 Datasheet(HTML) 180 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL