| Electronic Components Datasheet Search |
|
MAX5152BEEE Datasheet(PDF) 10 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
MAX5152BEEE Datasheet(HTML) 10 Page - Maxim Integrated Products |
|
10 / 20 page ![]() Power-Down Mode The MAX5152/MAX5153 feature a software-program- mable shutdown mode that reduces the typical supply current to 2µA. The two DACs can be shut down inde- pendently or simultaneously by using the appropriate programming word. For instance, enter shutdown mode (for both DACs) by writing an input control word of 111XXXXXXXXXXXXX (Table 1). In shutdown mode, the reference inputs and amplifier outputs become high impedance, and the serial interface remains active. Data in the input registers is saved, allowing the MAX5152/MAX5153 to recall the output state prior to entering shutdown when returning to normal mode. Exit shutdown by recalling the previous condition or by updating the DAC with new information. When returning to normal operation (exiting shutdown), wait 20µs for output stabilization. Serial Interface The MAX5152/MAX5153 3-wire serial interface is com- patible with both Microwire (Figure 2) and SPI/QSPI (Figure 3) serial-interface standards. The 16-bit serial input word consists of an address bit, two control bits, and 13 bits of data (MSB to LSB) as shown in Figure 4. The address and control bits determines the response of the MAX5152/MAX5153, as outlined in Table 1. The MAX5152/MAX5153’s digital inputs are double buffered, which allows any of the following: loading the input register(s) without updating the DAC register(s), updating the DAC register(s) from the input register(s), or updating the input and DAC registers concurrently. The address and control bits allow for the DACs to act independently. Low-Power, Dual, 13-Bit Voltage-Output DACs with Configurable Outputs 10 ______________________________________________________________________________________ D12................D0 MSB LSB 16-BIT SERIAL WORD FUNCTION A0 C1 C0 0 0 1 13 bits of DAC data Load input register A; DAC register is unchanged. 0 1 1 13 bits of DAC data Load all DAC registers from the shift register (start up both DACs with new data). 1 1 0 13 bits of DAC data Load input register B; all DAC registers are updated. 0 1 0 13 bits of DAC data Load input register A; all DAC registers are updated. 1 0 1 13 bits of DAC data Load input register B; DAC register is unchanged. 0 0 0 1 1 0 x xxxxxxxxx Shut down DAC A when PDL = 1. 0 0 0 1 0 1 x xxxxxxxxx Update DAC register B from input register B (start up DAC B with data previ- ously stored in input register B). 0 0 0 0 0 1 x xxxxxxxxx Update DAC register A from input register A (start up DAC A with data previ- ously stored in input register A). 1 1 1 xxxxxxxxxxxxx Shut down both DACs if PDL = 1. 1 0 0 xxxxxxxxxxxxx Update both DAC registers from their respective input registers (start up both DACs with data previously stored in the input registers). 0 0 0 1 1 1 x xxxxxxxxx Shut down DAC B when PDL = 1. 0 0 0 0 1 0 x xxxxxxxxx UPO goes low (default). 0 0 0 0 1 1 x xxxxxxxxx UPO goes high. 0 0 0 1 0 0 1 xxxxxxxxx Mode 1, DOUT clocked out on SCLK’s rising edge. 0 0 0 1 0 0 0 xxxxxxxxx Mode 0, DOUT clocked out on SCLK’s falling edge (default). 0 0 0 0 0 0 x xxxxxxxxx No operation (NOP). Table 1. Serial-Interface Programming Commands “x” = don’t care Note: When A0, C1, and C0 = “0”, D12, D11, D10, and D9 become control bits. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |