| Electronic Components Datasheet Search |
|
MAX5152BEEE Datasheet(PDF) 11 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
MAX5152BEEE Datasheet(HTML) 11 Page - Maxim Integrated Products |
|
11 / 20 page ![]() Send the 16-bit data as two 8-bit packets (SPI, Microwire) or one 16-bit word (QSPI), with CS low dur- ing this period. The address and control bits determine which register will be updated, as well as the state of the registers when exiting shutdown. The 3-bit address/control determines: • registers to be updated • clock edge on which data is clocked out via the seri- al data output (DOUT) • state of the user-programmable logic output • configuration of the device after shutdown The general timing diagram in Figure 5 illustrates how data is acquired. Driving CS low enables the device to receive data. Otherwise, the interface control circuitry is disabled. With CS low, data at DIN is clocked into the register on the rising edge of SCLK. As CS goes high, data is latched into the input and/or DAC registers depending on the address and control bits. The maxi- mum clock frequency guaranteed for proper operation is 10MHz. Figure 6 depicts a more detailed timing dia- gram of the serial interface. Serial Data Output (DOUT) DOUT is the internal shift register’s output. It allows for daisy-chaining and data readback. The MAX5152/ MAX5153 can be programmed to shift data out of DOUT on SCLK’s falling edge (Mode 0) or rising edge (Mode 1). Mode 0 provides a lag of 16 clock cycles, which maintains compatibility with SPI/QSPI and Microwire interfaces. In Mode 1, the output data lags 15.5 clock cycles. On power-up, the device defaults to Mode 0. User-Programmable Logic Output (UPO) UPO allows an external device to be controlled through the MAX5152/MAX5153 serial interface (Table 1), there- by reducing the number of microcontroller I/O pins required. On power-up, UPO is low. Power-Down Lockout Input (PDL) PDL disables software shutdown when low. When in shutdown, transitioning PDL from high to low wakes up the part with the output set to the state prior to shut- down. PDL can also be used to asynchronously wake up the device. Daisy Chaining Devices Any number of MAX5152/MAX5153s can be daisy chained by connecting the DOUT pin of one device to the DIN pin of the following device in the chain (Figure 7). Low-Power, Dual, 13-Bit Voltage-Output DACs with Configurable Outputs ______________________________________________________________________________________ 11 SCLK DIN CS SK SO I/O MAX5152 MAX5153 MICROWIRE PORT Figure 2. Connections for Microwire DIN SCLK CS MOSI SCK I/O SPI/QSPI PORT SS VCC CPOL = 0, CPHA = 0 MAX5152 MAX5153 Figure 3. Connections for SPI/QSPI Figure 4. Serial-Data Format 1 Address/2 Control Bits A0 MSB ..................................................................................LSB Address Bits C1, C0 Control Bits 16 Bits of Serial Data 13 Data Bits D12.................................D0 MSB.......Data Bits.........LSB |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |