Electronic Components Datasheet Search
  English  ▼

X  

MIC5018 Datasheet(PDF) 6 Page - Micrel Semiconductor

Part # MIC5018
Description  IttyBitty??High-Side MOSFET Driver Preliminary Information
PDF  7 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  MICREL [Micrel Semiconductor]
Direct Link  http://www.micrel.com
Logo MICREL - Micrel Semiconductor

MIC5018 Datasheet(HTML) 6 Page - Micrel Semiconductor

  MIC5018 Datasheet HTML 1Page - Micrel Semiconductor MIC5018 Datasheet HTML 2Page - Micrel Semiconductor MIC5018 Datasheet HTML 3Page - Micrel Semiconductor MIC5018 Datasheet HTML 4Page - Micrel Semiconductor MIC5018 Datasheet HTML 5Page - Micrel Semiconductor MIC5018 Datasheet HTML 6Page - Micrel Semiconductor MIC5018 Datasheet HTML 7Page - Micrel Semiconductor  
Zoom Inzoom in Zoom Outzoom out
 6 / 7 page
background image
MIC5018
Micrel
5-160
1997
Application Information
Supply Bypass
A capacitor from VS to GND is recommended to control
switching and supply transients. Load current and supply
lead length are some of the factors that affect capacitor
size requirements.
A 4.7
µF or 10µF aluminum electrolytic or tantalum capacitor
is suitable for many applications.
The low ESR (equivalent series resistance) of tantalum
capacitors makes them especially effective, but also makes
them susceptible to uncontrolled inrush current from low
impedance voltage sources (such as NiCd batteries or auto-
matic test equipment). Avoid instantaneously applying volt-
age, capable of high peak current, directly to or near tantalum
capacitors without additional current limiting. Normal power
supply turn-on (slow rise time) or printed circuit trace resis-
tance is usually adequate for normal product usage.
MOSFET Selection
The MIC5018 is designed to drive N-channel enhancement-
type MOSFETs. The gate output (G) of the MIC5018 pro-
vides a voltage, referenced to ground, that is greater than the
supply voltage. Refer to the “Typical Characteristics: Gate
Output Voltage vs. Supply Voltage” graph.
The supply voltage and the MOSFET drain-to-source
voltage drop determine the gate-to-source voltage.
V
GS = VG – (VSUPPLY – VDS)
where:
V
GS = gate-to-source voltage (enhancement)
V
G = gate voltage (from graph)
V
SUPPLY = supply voltage
V
DS = drain-to-source voltage (approx. 0V at
low current, or when fully enhanced)
VS
CTL
G
GND
MIC5018
VSUPPLY
1
23
4
VGS
VDS
VLOAD
VGG
D
S
Figure 1. Voltages
The performance of the MOSFET is determined by the gate-
to-source voltage. Choose the type of MOSFET according to
the calculated gate-to-source voltage.
Standard MOSFET
Standard MOSFETs are fully enhanced with a gate-to-source
voltage of about 10V. Their absolute maximum gate-to-
source voltage is
±20V.
With a 5V supply, the MIC5018 produces a gate output of
approximately 15V.
Figure 2 shows how the remaining
voltages conform. The actual drain-to-source voltage drop
across an IRFZ24 is less than 0.1V with a 1A load and 10V
enhancement. Higher current increases the drain-to-source
voltage drop, increasing the gate-to-source voltage.
VS
CTL
G
GND
MIC5018
4.7µF
+5V
1
23
4
Logic
High
10V
approx. 0V
5V
15V
Voltages are approximate
* International Rectifier
standard MOSFET
IRFZ24*
To demonstrate
this circuit, try a
2
Ω, 20W
load resistor .
Figure 2. Using a Standard MOSFET
The MIC5018 has an internal zener diode that limits the gate-
to-ground voltage to approximately 16V.
Lower supply voltages, such as 3.3V, produce lower gate
output voltages which will not fully enhance standard
MOSFETs. This significantly reduces the maximum current
that can be switched. Always refer to the MOSFET data sheet
to predict the MOSFET’s performance in specific applica-
tions.
Logic-Level MOSFET
Logic-level N-channel MOSFETs are fully enhanced with a
gate-to-source voltage of approximately 5V and generally
have an absolute maximum gate-to-source voltage of
±10V.
VS
CTL
G
GND
MIC5018
4.7µF
+3.3V
1
23
4
Logic
High
5.7V
approx. 0V
3.3V
9V
Voltages are approximate
* International Rectifier
logic-level MOSFET
IRLZ44*
To demonstrate
this circuit, try
5
Ω, 5W or
47
Ω, 1/4W
load resistors.
Figure 3. Using a Logic-Level MOSFET
Refer to figure 3 for an example showing nominal voltages.
The maximum gate-to-source voltage rating of a logic-level
MOSFET can be exceeded if a higher supply voltage is used.
An external zener diode can clamp the gate-to-source volt-
age as shown in figure 4.
The zener voltage, plus its
tolerance, must not exceed the absolute maximum gate
voltage of the MOSFET.
VS
CTL
G
GND
MIC5018
VSUPPLY
1
23
4
5V < VZ < 10V
Protects gate of
logic-level MOSFET
Logic-level
N-channel
MOSFET
Figure 4. Gate-to-Source Protection



Html Pages

1 2 3 4 5 6 7


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com