ADAV4601BSTZ datasheet(22/60 Pages) AD

22 / 60 page

ADAV4601

Rev. B | Page 22 of 60

DAC VOLTAGE OUTPUTS

The ADAV4601 has six DAC outputs, configured as 3-stereo

auxiliary DAC outputs. However, because the flow is customizable,

it is programmable. The output level is 1 V rms full scale. The DAC

outputs should have a 10 nF capacitor to ground for filtering out

high frequency noise. Following the filtering capacitor, a 10 μF

is required for dc blocking.

After reset, the DACs are in a power-down state. They can power

up quickly using the global power-up in the initialization control

down are also possible.

In power critical applications, it is possible to use the Analog

Power Management 1 register (0x0005) to power up or power

down individual DACs.

AUXOUT1L

AUXOUT1R

AUXOUT3L

AUXOUT3R

AUXOUT4L

AUXOUT4R

10µF

10nF

10µF

10nF

DAC

10µF

10nF

10µF

10nF

DAC

10µF

10nF

10µF

10nF

DAC

Figure 30. DAC Output Section

PWM OUTPUTS

In the ADAV4601, the main outputs are available as four PWM

output channels, which are suitable for driving Class-D amplifiers.

After reset, the PWM channels are in a power-down state. Writing

to the miscellaneous control register (0x000A) enables the PWM

channels. To help ensure popless and clickless power-up and

power-down, there is an enable/disable pattern that is specially

constructed to bring the PWM channels from a zero condition

to a 50/50 duty-cycle square wave (effectively, a zero signal into

the PWM block). This takes 365 ms to complete and can be seen in

Figure 33.

Designed for use in conjunction with this ramp-up scheme, the

ADAV4601 features a status pin, PWM_READY, that indicates

when the PWM outputs are in a state that can cause pops/clicks,

such as power-up and power-down. During PWM power-up

and power-down, this pin remains low to signify that the

outputs are not in a valid state. This functionality helps to

eliminate pop/click and other unwanted noise on the outputs.

To accommodate different power stages, the point at which the

PWM_READY signal goes high is programmable. It can go

high when the PWM outputs begin their ramp-up scheme

(PWM_READY early), or it can be programmed to go high

when this ramp-up scheme is complete (PWM_READY late).

This is shown in Figure 33, and it is configured in the PWM

control register (0x001F).

Each set of PWM outputs comprises complementary outputs.

The modulation frequency is 384 kHz, and the full-scale duty

cycle has a ratio of 97:3.

PWM1A

PWM1B

PWM2A

PWM2B

PWM3A

PWM3B

PWM

MODULATOR

PWM

MODULATOR

PWM

MODULATOR

–

PWM4A

PWM_READY

PWM4B

PWM

MODULATOR

–

Figure 31. PWM Output Section

HEADPHONE OUTPUT

There is a dedicated stereo headphone amplifier output that is

capable of driving 32 Ω loads at 1 V rms.

After reset, the headphone output is tristated. The tristate is

disabled using the headphone control register (0x000B). Using

the same register, the gain of the headphone amplifier can be set in

+1.5 dB steps from +1.5 dB to −45 dB. The headphone output

should have a 10 μF capacitor for dc blocking.

HPOUT1L

AUXOUT4L

AUXOUT4R

HPOUT1R

10µF

DAC

Figure 32. Headphone Output Section

PWM1A

PWM1B

PWM READY

PWM READY EARLY

PWM READY LATE

DIFFERENTIAL PWM

IN PHASE

DIFFERENTIAL PWM

OUT OF PHASE—

VALID AUDIO

365ms

206µs

Figure 33. PWM Early

ADAV4601BSTZ Datasheet(PDF) 22 Page - Analog Devices

ADAV4601BSTZ Datasheet(HTML) 22 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Datasheet Download

Link URL