COP8ACC7 datasheet(13/40 Pages) NSC

13 / 40 page

Oscillator Circuits (Continued)

Control Registers

CNTRL Register (Address X'00EE)

T1C3

T1C2

T1C1

T1C0

MSEL

IEDG

SL1

SL0

Bit 7

Bit 0

The Timer1 (T1) and MICROWIRE/PLUS control register

contains the following bits:

T1C3

Timer T1 mode control bit

T1C2

Timer T1 mode control bit

T1C1

Timer T1 mode control bit

T1C0

Timer T1 Start/Stop control in timer

modes 1 and 2, T1 Underflow Interrupt

Pending Flag in timer mode 3

MSEL

Selects G5 and G4 as MICROWIRE/PLUS

signals SK and SO respectively

IEDG

External interrupt edge polarity select

(0 = Rising edge, 1 = Falling edge)

SL1 & SL0

Select the MICROWIRE/PLUS clock divide

by (00 = 2, 01 = 4, 1x = 8)

PSW Register (Address X'00EF)

T1PNDA

T1ENA

EXPND

BUSY

EXEN

GIE

Bit 7

Bit 0

The PSW register contains the following select bits:

Half Carry Flag

Carry Flag

T1PNDA Timer T1 Interrupt Pending Flag (Autoreload

RA in mode 1, T1 Underflow in Mode 2, T1A

capture edge in mode 3)

T1ENA

Timer T1 Interrupt Enable for Timer Underflow

or T1A Input capture edge

EXPND

External interrupt pending

BUSY

MICROWIRE/PLUS busy shifting flag

EXEN

Enable external interrupt

GIE

Global interrupt enable (enables interrupts)

The Half-Carry flag is also affected by all the instructions that

affect the Carry flag. The SC (Set Carry) and R/C (Reset

Carry) instructions will respectively set or clear both the carry

flags. In addition to the SC and R/C instructions, ADC,

SUBC, RRC and RLC instructions affect the Carry and Half

Carry flags.

ICNTRL Register (Address X'00E8)

Reserved

LPEN

T0PND

T0EN

µWPND

µWEN

T1PNDB

T1ENB

Bit 7

Bit 0

The ICNTRL register contains the following bits:

Reserved This bit is reserved and should be zero.

LPEN

L Port Interrupt Enable (Multi-Input Wakeup/

Interrupt)

T0PND

Timer T0 Interrupt pending

T0EN

Timer T0 Interrupt Enable (Bit 12 toggle)

µWPND

MICROWIRE/PLUS interrupt pending

µWEN

Enable MICROWIRE/PLUS interrupt

T1PNDB

Timer T1 Interrupt Pending Flag for T1B cap-

ture edge

T1ENB

Timer T1 Interrupt Enable for T1B Input cap-

ture edge

Timers

The device contains a very versatile set of timers (T0 and

T1). All timers and associated autoreload/capture registers

power up containing random data.

TIMER T0 (IDLE TIMER)

The device supports applications that require maintaining

real time and low power with the IDLE mode. This IDLE

mode support is furnished by the IDLE timer T0, which is a

16-bit timer. The Timer T0 runs continuously at the fixed rate

of the instruction cycle clock, t

C. The user cannot read or

write to the IDLE Timer T0, which is a count down timer.

The Timer T0 supports the following functions:

•

Exit out of the Idle Mode (See Idle Mode description)

•

WATCHDOG logic (See WATCHDOG description)

•

Start up delay out of the HALT mode

is a functional block diagram showing the structure of the

IDLE Timer and its associated interrupt logic.

Bits 11 through 15 of the ITMR register can be selected for

triggering the IDLE Timer interrupt. Each time the selected

bit underflows (every 4k, 8k, 16k, 32k or 64k instruction

cycles), the IDLE Timer interrupt pending bit T0PND is set,

thus generating an interrupt (if enabled), and bit 6 of the Port

G data register is reset, thus causing an exit from the IDLE

mode if the device is in that mode.

In order for an interrupt to be generated, the IDLE Timer in-

terrupt enable bit T0EN must be set, and the GIE (Global In-

terrupt Enable) bit must also be set. The T0PND flag and

T0EN bit are bits 5 and 4 of the ICNTRL register, respec-

tively. The interrupt can be used for any purpose. Typically, it

is used to perform a task upon exit from the IDLE mode. For

more information on the IDLE mode, refer to the Power Save

Modes section.

The Idle Timer period is selected by bits 0–2 of the ITMR

should not be used as software flags.

DS012869-7

DS012869-8

FIGURE 7. Crystal and R/C Oscillator Diagrams

COP8ACC7 Datasheet(PDF) 13 Page - National Semiconductor (TI)

COP8ACC7 Datasheet(HTML) 13 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

Datasheet Download

Link URL