| Electronic Components Datasheet Search |
|
AD9289 Datasheet(PDF) 9 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
AD9289 Datasheet(HTML) 9 Page - Analog Devices |
|
9 / 16 page ![]() Preliminary Technical Data AD9289 Rev. PrJ | Page 9 of 16 6/25/2004 THEORY OF OPERATION Each A/D converter in the AD9289 architecture consists of a front- end sample and hold amplifier (SHA) followed by a pipelined switched capacitor A/D converter. The pipelined A/D converter is divided into two sections, consisting of six 1.5-bit stages and a final 3-bit flash. Each stage provides sufficient overlap to correct for flash errors in the preceding stages. The quantized outputs from each stage are combined into a final 8-bit result in the digital correction logic. The pipelined architecture permits the first stage to operate on a new input sample while the remaining stages operate on preceding samples. Sampling occurs on the rising edge of the clock. Each stage of the pipeline, excluding the last, consists of a low resolution flash A/D connected to a switched capacitor DAC and interstage residue amplifier (MDAC). The residue amplifier magnifies the difference between the reconstructed DAC output and the flash input for the next stage in the pipeline. One bit of redundancy is used in each one of the stages to facilitate digital correction of flash errors. The last stage simply consists of a flash A/D. The input stage contains a differential SHA that can be configured as ac- or dc-coupled in differential or single -ended modes. The output-staging block aligns the data, carries out the error correction and passes the data to the output buffers.During power-down the output buffers go into a high-impedance state. Clock Input Typical high-speed A/D converters use both clock edges to generate a variety of internal timing signals, and as a result may be sensitive to clock duty cycle. Commonly a +/-5% tolerance is required on the clock duty cycle to maintain dynamic performance characteristics. The AD9289 contains a clock duty cycle stabilizer that retimes the non-sampling edge, providing an internal clock signal with a nominal 50% duty cycle. This allows a wide range of clock input duty cycles without affecting the performance of the AD9289. As shown in TPC XX, noise and distortion performance are nearly flat over at least a +/-15% range of duty cycle. The stabilizer circuit can be bypassed by grounding input pin DCR. ( There is an internal 22K ohm pull-up resistor) The duty cycle stabilizer uses a delay-locked loop (DLL) to create the non-sampling edge. As a result, any changes to the sampling frequency will require approximately 100 clock cycles to allow the DLL to acquire and lock to the new rate. High-speed, high- resolution A/Ds are sensitive to the quality of the clock input. The degradation in SNR at a given full-scale input frequency (fA) due only to aperture jitter (tA) can be calculated with the following equation: SNR degradation = 20 × log10 [1/2 × pi × fA × tA] In the equation, the rms aperture jitter, tA, represents the root sum square of all jitter sources, which include the clock input, analog input signal, and A/D aperture jitter specification. Undersampling applications are particularly sensitive to jitter. The clock input should be treated as an analog signal in cases where aperture jitter may affect the dynamic range of the AD9289. Power supplies for clock drivers should be separated from the A/D output driver supplies to avoid modulating the clock signal with digital noise. Low jitter, crystal-controlled oscillators make the best clock sources. If the clock is generated from another type of source (by gating, dividing, or other methods), it should be retimed by the original clock at the last step. Analog Inputs For best dynamic performance, the source impedances driving VIN+ and VIN– should be matched such that common-mode settling errors are symmetrical. These errors will be reduced by the common-mode rejection of the A/D. Voltage Reference A stable and accurate 0.5 V voltage reference is built into the AD9289. The input range can be adjusted by varying the reference voltage applied to the AD9289, using either the internal reference or an externally applied reference voltage. The input span of the A/D tracks reference voltage changes linearly. The Shared Reference mode allows the user to connect the references from the quad ADC together externally for superior gain and offset matching performance. If the ADCs are to function independently, the reference decoupling can be treated independently and can provide superior isolation between the four channels. To enable Shared Reference mode, the SHARED_REF pin must be tied high and external differential references must be externally shorted. (REFT_A must be externally shorted to REFT_B and REFB_A must be shorted to REFB_B.) Note that channels A and B are referenced to REFT_A and REFB_A and channels C and D are referenced to REFT_B and REFB_B. Figure 3. Shared Reference Mode |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |