 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
UCS81003 Datasheet(PDF) 69 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
UCS81003 Datasheet(HTML) 69 Page - Microchip Technology |
|
|
69 / 108 page  2014 Microchip Technology Inc. DS20005334A-page 69 UCS81003 bit 3-0 S1_R1<3:0>: Defines the stimulus response as shown below:. 0000 = Remove previous response on DPOUT and DMOUT 0001 = Apply voltage on DPOUT (Note 1). 0010 = Apply voltage on DMOUT (Note 2). 0011 = Apply voltage on DPOUT and DMOUT. 0100 = Connect resistor from DPOUT to GND (Note 1). 0101 = Do not use. 0110 = Connect voltage divider from VBUS to GND with “center” at DPOUT (Note 1). 0111 = Connect resistor form DMOUT to GND (Note 2). 1000 = Do not use. 1001 = Connect voltage divider from VBUS to GND with “center” at DMOUT (Note 2). 1010 = Connect 200resistor from D POUT to DMOUT. 1011 = Do not use. 1100 = Connect voltage divider from VBUS to GND with ‘center’ at DPOUT and DMOUT. 1101 = Connect resistor from DPOUT to GND and DMOUT to GND. 1110 = If STIM1 = 000, the 15 k pull down resistors applied to D POUT and DMOUT during emulation reset are not removed. If STIM1 = 111, the 15 k pull down resistors applied to D POUT and DMOUT during emula- tion reset are removed. For all other STIM1 settings, whatever was applied is not changed. 1111 = Same as 1110 case above. Note 1: If STIM1<2:0> = 000b and no other response was applied to the DPOUT pin, the 15 k pull-down resistor applied to the DPOUT pin during emulation reset is not removed. Otherwise, the previous response is left on the DPOUT pin (if applicable) or the 15 k pull-down resistor is removed. 2: If STIM1<2:0> = 000b and no other response was applied to the DMOUT pin, the 15 k pull-down resistor applied to the DMOUT pin during emulation reset is not removed. Otherwise, the previous response is left on the DMOUT pin (if applicable) or the 15 k pull-down resistor is removed. REGISTER 10-26: PRELOADED EMULATION STIMULUS 1 CONFIGURATION 3 REGISTER (ADDRESS 33H)(Note 1) U-x U-x R-0 R-0 R-0 R-0 R-0 R-0 — — S1_PUPD<1:0> S1_TH<3:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-6 Unimplemented bit 5-4 S1_PUPD<1:0>: Determines the magnitude of the pull-down current applied on the DPOUT and DMOUT pins when the stimulus response is to apply a voltage and the voltage magnitude is set at pull-down (0000b). The bit decode is given below. 00 = 10 µA 01 = 50 µA 10 = 100 µA 11 = 150 µA REGISTER 10-25: PRELOADED EMULATION STIMULUS 1 CONFIGURATION 2 REGISTER (ADDRESS 32H) (CONTINUED) |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
