| Electronic Components Datasheet Search |
|
HCTL1100 Datasheet(PDF) 13 Page - Agilent(Hewlett-Packard) |
|
|
|||||||||||||||||||||||||||||
HCTL1100 Datasheet(HTML) 13 Page - Agilent(Hewlett-Packard) |
|
13 / 40 page ![]() 13 Output Pins Pin Number Symbol PDIP PLCC Description MC0-MC7 18-25 20-22, Motor Command Port – 8-bit output port which contains the digital 24-28 motor command adjusted for easy bipolar DAC interfacing. MC7 is the most significant bit (MSB). Pulse 16 18 Pulse – Pulse width modulated signal whose duty cycle is proportional to the Motor Command magnitude. The frequency of the signal is External Clock/100 and pulse width is resolved into 100 external clocks. Sign 17 19 Sign – Gives the sign/direction of the pulse signal. PHA-PHD 26-29 29-32 Phase A, B, C, D – Phase Enable outputs of the Commutator. Prof 12 13 Profile Flag – Status flag which indicates that the controller is execut- ing a profiled position move in the Trapezoidal Profile Control mode. Init 13 14 Initialization/Idle Flag – Status flag which indicates that the controller is in the Initialization/Idle mode. Pin Functionality SYNC Pin The SYNC pin is used to syn- chronize two or more ICs. It is only valid in the INIT/IDLE mode (see Operating the HCTL-1100). When this pin is pulled low, the internal sample timer is cleared and held to zero. When the level on the pin is returned to high, the internal sample timer instantly starts counting down from the programmed value. Connecting all SYNC pins together in the system and pulsing the SYNC signal from the host processor will synchronize all controllers. Limit Pin This emergency-flag input is used to disable the control modes of the HCTL-1100. A low level on this input pin causes the internal Limit flag to be set. If this pin is NOT used, it must be pulled up to VDD. If it is not connected, the pin could float low, and possibly trigger a false emergency condition. The Limit flag, when set in any control mode, causes the HCTL- 1100 to go into the Initialization/ Idle mode, clearing the Motor Command and causing an imme- diate motor shutdown. When the Limit flag is set, none of the three control mode flags (F0, F3, or F5) are cleared as the HCTL-1100 enters the Initialization/Idle mode. The user should be aware that these flags are still set before commanding the HCTL-1100 to re-enter one of the four control modes from Initialization/Idle mode. In general, the user should clear all control mode flags after the limit pin has been pulled low, then proceed. Stop Pin The Stop flag affects the HCTL- 1100 only in the Integral Velocity Mode. When a low level is present on this emergency-flag input, the internal stop flag is set. If this pin is NOT used, it must be pulled up to VDD. If it is not connected, the pin could float low, and possibly trigger a false emergency condition. When the STOP flag is set, the system will come to a decelerated stop and stay in this mode with a command velocity of zero until the Stop flag is cleared and a new command velocity is specified. Notes on Limit and Stop Flags Stop and Limit flags are set by a low level input at their respective pins. The flags can only be cleared when the input to the corresponding pin goes high, signifying that the emergency condition has been corrected, AND a write to the Status register (R07H) is executed. That is, after the emergency pin has been set and cleared, the flag also must be cleared by writing to R07H. Any word that is written to R07H after the emergency pin is set and cleared will clear the emergency flag. The lower four bits of that word will also reconfigure the Status register. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |