| Electronic Components Datasheet Search |
|
MT8880CS/CS-1 Datasheet(PDF) 2 Page - Mitel Networks Corporation |
|
|
|||||||||||||||||||||||||||||
MT8880CS/CS-1 Datasheet(HTML) 2 Page - Mitel Networks Corporation |
|
2 / 18 page ![]() MT8880C/MT8880C-1 ISO2-CMOS 4-34 Figure 2 - Pin Connections Pin Description Pin # Name Description 20 24 28 1 1 1 IN+ Non-inverting op-amp input. 2 2 2 IN- Inverting op-amp input. 334 GS Gain Select. Gives access to output of front end differential amplifier for connection of feedback resistor. 446VRef Reference Voltage output, nominally VDD/2 is used to bias inputs at mid-rail (see Fig. 13). 557 VSS Ground input (0V). 6 6 8 OSC1 DTMF clock/oscillator input. 7 7 9 OSC2 Clock output. A 3.579545 MHz crystal connected between OSC1 and OSC2 completes the internal oscillator circuit. Leave open circuit when OSC1 is clock input. 810 12 TONE Tone output (DTMF or single tone). 911 13 R/W Read/Write input. Controls the direction of data transfer to and from the MPU and the transceiver registers. TTL compatible. 10 12 14 CS Chip Select, TTL input (CS=0 to select the chip). 11 13 15 RS0 Register Select input. See register decode table. TTL compatible. 12 14 17 Φ2 System Clock input. TTL compatible. N.B. Φ2 clock input need not be active when the device is not being accessed. 13 15 18 IRQ/ CP Interrupt Request to MPU (open drain output). Also, when call progress (CP) mode has been selected and interrupt enabled the IRQ/CP pin will output a rectangular wave signal representative of the input signal applied at the input op-amp. The input signal must be within the bandwidth limits of the call progress filter. See Figure 8. 14- 17 18- 21 19- 22 D0-D3 Microprocessor Data Bus (TTL compatible). High impedance when CS = 1 or Φ2 is low. 18 22 26 ESt Early Steering output. Presents a logic high once the digital algorithm has detected a valid tone pair (signal condition). Any momentary loss of signal condition will cause ESt to return to a logic low. 19 23 27 St/GT Steering Input/Guard Time output (bidirectional). A voltage greater than VTSt detected at St causes the device to register the detected tone pair and update the output latch. A voltage less than VTSt frees the device to accept a new tone pair. The GT output acts to reset the external steering time-constant; its state is a function of ESt and the voltage on St. 20 24 28 VDD Positive power supply input (+5V typical). 8,9 16, 17 3,5, 10, 11, 16, 23- 25 NC No Connection. 1 2 3 4 5 6 7 8 9 10 11 12 20 19 18 17 16 15 14 13 IN+ IN- GS VRef VSS OSC1 OSC2 TONE R/W CS VDD St/GT ESt D3 D2 D1 D0 IRQ/CP Φ2 RS0 20 PIN CERDIP/PLASTIC DIP/SOIC 28 PIN PLCC 5 6 7 8 9 10 11 25 24 23 22 21 20 19 • NC VRef VSS OSC1 OSC2 NC NC NC NC NC D3 D2 D1 D0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 24 23 22 21 20 19 18 17 IN+ IN- GS VRef VSS OSC1 OSC2 NC TONE R/W CS VDD St/GT ESt D3 D2 D1 D0 NC NC NC IRQ/CP Φ2 RS0 24 PIN SSOP |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |