Electronic Components Datasheet Search
  English  ▼

X  

AD5308 Datasheet(PDF) 12 Page - Analog Devices

Part # AD5308
Description  2.5 V to 5.5 V Octal Voltage Output 8-/10-/12-Bit DACs in 16-Lead TSSOP
PDF  19 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

AD5308 Datasheet(HTML) 12 Page - Analog Devices

Back Button AD5308 Datasheet HTML 8Page - Analog Devices AD5308 Datasheet HTML 9Page - Analog Devices AD5308 Datasheet HTML 10Page - Analog Devices AD5308 Datasheet HTML 11Page - Analog Devices AD5308 Datasheet HTML 12Page - Analog Devices AD5308 Datasheet HTML 13Page - Analog Devices AD5308 Datasheet HTML 14Page - Analog Devices AD5308 Datasheet HTML 15Page - Analog Devices AD5308 Datasheet HTML 16Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 12 / 19 page
background image
REV. B
–12–
AD5308/AD5318/AD5328
SERIAL INTERFACE
The AD5308/AD5318/AD5328 are controlled over a versatile
3-wire serial interface that operates at clock rates up to 30 MHz
and is compatible with SPI, QSPI, MICROWIRE, and DSP
interface standards.
Input Shift Register
The input shift register is 16 bits wide. Data is loaded into the
device as a 16-bit word under the control of a serial clock input,
SCLK. The timing diagram for this operation is shown in Figure 1.
The
SYNC input is a level-triggered input that acts as a frame
synchronization signal and chip enable. Data can be transferred
into the device only while
SYNC is low. To start the serial
data transfer,
SYNC should be taken low, observing the mini-
mum
SYNC to SCLK falling edge setup time, t
4. After SYNC
goes low, serial data will be shifted into the device’s input shift
register on the falling edges of SCLK for 16 clock pulses.
To end the transfer,
SYNC must be taken high after the falling
edge of the 16th SCLK pulse, observing the minimum SCLK
falling edge to
SYNC rising edge time, t
7.
After the end of serial data transfer, data will automatically be
transferred from the input shift register to the input register of
the selected DAC. If
SYNC is taken high before the 16th falling
edge of SCLK, the data transfer will be aborted and the DAC
input registers will not be updated.
Data is loaded MSB first (Bit 15). The first bit determines whether
it is a DAC write or a control function.
DAC Write
Here, the 16-bit word consists of one control bit and three
address bits followed by 8, 10, or 12 bits of DAC data, depending
on the device type. In the case of a DAC write, the MSB will be
a 0. The next three address bits determine whether the data is
for DAC A, DAC B, DAC C, DAC D, DAC E, DAC F, DAC
G, or DAC H. The AD5328 uses all 12 bits of DAC data. The
AD5318 uses 10 bits and ignores the two LSBs. The AD5308
uses eight bits and ignores the last four bits. These ignored
LSBs should be set to 0. The data format is straight binary,
with all 0s corresponding to 0 V output and all 1s corresponding
to full-scale output.
Table I. Address Bits for the AD53x8
A2 (Bit 14)
A1 (Bit 13)
A0 (Bit 12)
DAC Addressed
0
0
0
DAC A
0
0
1
DAC B
0
1
0
DAC C
0
1
1
DAC D
1
0
0
DAC E
1
0
1
DAC F
1
1
0
DAC G
1
1
1
DAC H
Control Functions
In the case of a control function, the MSB (Bit 15) will be a 1.
This is followed by two control bits, which determine the mode.
There are four different control modes, each of which is described
below. The write sequences for these modes are shown in Table II.
Reference and Gain Mode
This mode determines whether the reference for each group of
DACs is buffered, unbuffered, or from VDD. It also determines
the gain of the output amplifier. To set up the reference of both
groups, set the control bits to (00), set the GAIN bits, set the
BUF bits, and set the VDD bits.
BUF
Controls whether the reference of a group of DACs is
buffered or unbuffered. The reference of the first group of
DACs (A, B, C, and D) is controlled by setting Bit 2, and
the second group of DACs (E, F, G, and H) is con-
trolled by setting Bit 3.
0: Unbuffered reference.
1: Buffered reference.
GAIN The gain of the DACs is controlled by setting Bit 4 for
the first group of DACs (A, B, C, and D) and Bit 5 for
the second group of DACs (E, F, G, and H).
0: Output range of 0 V to VREF.
1: Output range of 0 V to 2 VREF.
D/C
A0
D7
D6
D5
D4
D3
D2
D1
D0
0000
BIT 0
(LSB)
BIT 15
(MSB)
DATA BITS
A1
A2
Figure 6. AD5308 Input Shift Register Contents
DATA BITS
A0
00
BIT 0
(LSB)
BIT 15
(MSB)
A1
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
A2
D/C
Figure 7. AD5318 Input Shift Register Contents
DATA BITS
D/C
A0
BIT 0
(LSB)
BIT 15
(MSB)
A1
A2
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
D10
D11
Figure 8. AD5328 Input Shift Register Contents



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com