Electronic Components Datasheet Search
  English  ▼

X  

LTC3255 Datasheet(PDF) 17 Page - Linear Technology

Part # LTC3255
Description  Fixed Ratio High Power Inductorless (Charge Pump) DC/DC Controller
PDF  28 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  LINER [Linear Technology]
Direct Link  http://www.linear.com
Logo LINER - Linear Technology

LTC3255 Datasheet(HTML) 17 Page - Linear Technology

Back Button LTC3255 Datasheet HTML 13Page - Linear Technology LTC3255 Datasheet HTML 14Page - Linear Technology LTC3255 Datasheet HTML 15Page - Linear Technology LTC3255 Datasheet HTML 16Page - Linear Technology LTC3255 Datasheet HTML 17Page - Linear Technology LTC3255 Datasheet HTML 18Page - Linear Technology LTC3255 Datasheet HTML 19Page - Linear Technology LTC3255 Datasheet HTML 20Page - Linear Technology LTC3255 Datasheet HTML 21Page - Linear Technology Next Button
Zoom Inzoom in Zoom Outzoom out
 17 / 28 page
background image
LTC7820
17
7820fc
For more information www.linear.com/LTC7820
Select the CTIMER such that the tCHARGE < tPRE-BALANCE.
If the flying capacitor CFLY and the output capacitor are
very large and input voltage is high, it may take several
pre-balance time periods to pre-balance the VLOW pin to
VHIGH_SENSE/2 with a fixed CTIMER. A longer start-up time
is expected. If there is a resistive load on the output, the
load current needs to be smaller than 93mA and still meet
tCHARGE = (COUT + CFLY) • VIN/2/(93mA – ILOAD) < tPRE-
BALANCE. Otherwise a disconnect FET may be required to
disconnect the load during startup.
Input/Output Capacitor and Flying Capacitor Selection
In high power switched capacitor applications, large AC
currents flow through the flying capacitors and input/
output capacitors. Low ESR ceramic capacitors are highly
recommended for high power switch capacitor applica-
tions. Make sure the maximum RMS capacitor current is
within the spec; or higher RMS current rated capacitors
are preferred. Note that capacitor manufacturers’ ripple
current ratings are often based on only 2000 hours of life.
This makes it advisable to further derate the capacitor, or
to choose capacitors rated at a higher temperature than
required. Several capacitors may be paralleled to meet
size or height requirements in the design.
The RMS current on the flying capacitors depends on their
capacitance and the switching frequency. Higher capaci-
tanceandhigherswitchingfrequencyresultsinlowerRMS
current.Foragoodtrade-offbetweenefficiencyandpower
density, the RMS current on the flying capacitors should
be lower than 140% of the maximum load current. If there
are N identical flying capacitors in parallel, the maximum
RMS current through each capacitor is:
IRMS_CFLY = IOUT(MAX) • 140%/N
The input capacitor RMS current is approximately half of
the load current. The input capacitor has to be selected
to accommodate the maximum load conditions. LTspice
simulation tool can be used to quantify the RMS current.
APPLICATIONS INFORMATION
Power MOSFETs and Schottky Diodes Selection
Four external N-channel MOSFETs must be selected for
each LTC7820 controller. Four internal gate drivers are
designed to drive the MOSFETs. The driver voltages are
decided by the INTVCC voltage, schottky diodes forward
voltage drop and switching frequency. The lowest driver
voltage is the top MOSFET M1 drive voltage running at
high switching frequency and cold temperature. It is
normallyaround4.2V.Consequently,logic-levelthreshold
MOSFETs must be used in most applications. Be aware
that the threshold voltage of some logic-level MOSFET
varies with temperature. If switching frequency is high
and temperature range is wide for specific applications,
the top driver voltage of MOSFET M1 may be as low as
4V, and sub-logic level threshold MOSFETs (VGS(TH) < 3V)
should be used. Selection criteria for the power MOSFETs
alsoincludetheon-resistanceRDS(ON),outputcapacitance
COSS, input voltage, and maximum output current. Gener-
ally, low RDS(ON) and low COSS MOSFETs are preferred in
switched capacitor applications since they will minimize
both conduction loss and switching loss. For a given input
and output voltage, the uppermost MOSFET M1 always
seeshighvoltageduringstart-upandshutdown.TheDrain
to Source voltage of M1 has to be high enough to survive
at full input voltage range. Other MOSFETs normally only
see half of the input voltage, so the breakdown voltage
of M2/M3/M4 can be lower than M1 to optimize RDS(ON)
and COSS. If the reliability of M1 is a major concern, the
same high voltage MOSFETs could also be used as M2/
M3/M4 to protect against M1 short conditions.
External schottky diodes are needed for the bootstrap
circuits, and provide voltage for the floating drivers. To
minimize the voltage drop on the top gate driver, low
forward voltage drop schottky diodes are preferred with
load current in the range of 10mA to 50mA. The reverse
breakdown voltage of the diodes should be high enough
to survive at the maximum operation voltage between the
VLOW and GND pins.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com