Electronic Components Datasheet Search
  English  ▼

X  

AD5415 Datasheet(PDF) 16 Page - Analog Devices

Part # AD5415
Description  Dual 12-Bit, High Bandwidth, Multiplying DAC
PDF  27 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

AD5415 Datasheet(HTML) 16 Page - Analog Devices

Back Button AD5415 Datasheet HTML 12Page - Analog Devices AD5415 Datasheet HTML 13Page - Analog Devices AD5415 Datasheet HTML 14Page - Analog Devices AD5415 Datasheet HTML 15Page - Analog Devices AD5415 Datasheet HTML 16Page - Analog Devices AD5415 Datasheet HTML 17Page - Analog Devices AD5415 Datasheet HTML 18Page - Analog Devices AD5415 Datasheet HTML 19Page - Analog Devices AD5415 Datasheet HTML 20Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 16 / 27 page
background image
AD5415
Data Sheet
Rev. F | Page 16 of 27
Bipolar Operation
In some applications, it may be necessary to generate full
4-quadrant multiplying operation or a bipolar output swing.
This can easily be accomplished by using another external
amplifier and the on-chip 4-quadrant resistors, as shown in
Figure 35.
When in bipolar mode, the output voltage is given by
VOUT = (VREF × D/2n − 1) − VREF
where:
D is the fractional representation, in the range of 0 to 4,095, of
the digital word loaded to the DAC.
n is the number of bits.
When VIN is an ac signal, the circuit performs 4-quadrant
multiplication.
Table 6 shows the relationship between digital code and the
expected output voltage for bipolar operation.
Table 6. Bipolar Code
Digital Input
Analog Output (V)
1111 1111 1111
+VREF (4095/4096)
1000 0000 0000
0
0000 0000 0001
−VREF (4095/4096)
0000 0000 0000
−VREF (4096/4096)
Stability
In the I-to-V configuration, the IOUT of the DAC and the inverting
node of the operational amplifier must be connected as close as
possible, and proper printed circuit board (PCB) layout techniques
must be used. Because every code change corresponds to a step
function, gain peaking may occur if the operational amplifier has
limited gain bandwidth product (GBP) and there is excessive par-
asitic capacitance at the inverting node. This parasitic capacitance
introduces a pole into the open-loop response, which can cause
ringing or instability in the closed-loop applications circuit.
An optional compensation capacitor, C1, can be added in parallel
with RFBA for stability, as shown in Figure 34 and Figure 35. Too
small a value of C1 can produce ringing at the output, whereas
too large a value can adversely affect the settling time. C1 must
be found empirically, but 1 pF to 2 pF is generally adequate for
the compensation.
IOUT1A
IOUT2A
RFBA
RFB
2R
R1
2R
AD5415
12-BIT DAC A
R
GND
SDIN
VREFA
SCLK
SYNC
R2
2R
R3
2R
R2A
R2_3A
R3A
VDD
C1
A1
VOUT = –VIN TO +VIN
A1
AGND
µCONTROLLER
R1A
AGND
AGND
VIN
NOTES
1. DAC B OMITTED FOR CLARITY.
2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED
IF A1 IS A HIGH SPEED AMPLIFIER.
Figure 35. Bipolar Operation
SINGLE-SUPPLY APPLICATIONS
Voltage Switching Mode of Operation
Figure 36 shows the DAC operating in the voltage switching
mode. The reference voltage, VIN, is applied to the IOUT1A pin,
IOUT2A is connected to AGND, and the output voltage is
available at the VREFA terminal. In this configuration, a positive
reference voltage results in a positive output voltage, making
single-supply operation possible. The output from the DAC is
voltage at a constant impedance (the DAC ladder resistance).
Therefore, an operational amplifier is necessary to buffer the
output voltage. The reference input no longer sees a constant
input impedance, but one that varies with code. Therefore, the
voltage input must be driven from a low impedance source.
VOUT
VDD
GND
VIN
IOUT2A
IOUT1A
RFBA VDD
VREFA
R2
R1
NOTES
1. SIMILAR CONFIGURATION FOR DACB
2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED
IF A1 IS A HIGH SPEED AMPLIFIER.
Figure 36. Single-Supply Voltage Switching Mode
Note that VIN is limited to low voltages because the switches in
the DAC ladder no longer have the same source-drain drive
voltage. As a result, the on resistance differs and degrades the
integral linearity of the DAC. Also, VIN must not go negative by
more than 0.3 V or an internal diode turns on, causing the device
to exceed the maximum ratings. In this type of application, the
full range of multiplying capability of the DAC is lost.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com