| Electronic Components Datasheet Search |
|
AD5415 Datasheet(PDF) 20 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
AD5415 Datasheet(HTML) 20 Page - Analog Devices |
|
20 / 27 page ![]() AD5415 Data Sheet Rev. F | Page 20 of 27 SERIAL INTERFACE The AD5415 has an easy to use 3-wire interface that is compatible with SPI, QSPI, MICROWIRE, and most DSP interface standards. Data is written to the device in 16-bit words. Each 16-bit word consists of four control bits and 12 data bits, as shown in Figure 39. Low Power Serial Interface To minimize the power consumption of the device, the interface only powers up fully when the device is being written to, that is, on the falling edge of SYNC. The SCLK and DIN input buffers are powered down on the rising edge of SYNC. DAC Control Bits C3 to C0 Control Bits C3 to C0 allow control of various functions of the DAC, as shown in Table 11. Default settings of the DAC at power on are as follows. Data is clocked into the shift register on falling clock edges, and daisy-chain mode is enabled. The device powers on with a zero-scale load to the DAC register and IOUT lines. The DAC control bits allow the user to adjust certain features at power on. For example, daisy-chaining can be disabled when not in use, an active clock edge can be changed to a rising edge, and DAC output can be cleared to either zero scale or midscale. The user can also initiate a readback of the DAC register contents for verification purposes. Control Register (Control Bits = 1101) While maintaining software compatibility with single-channel current output DACs (AD5426/AD5433/AD5443), this DAC also features additional interface functionality. Simply set the control bits to 1101 to enter control register mode. Figure 40 shows the contents of the control register, the functions of which are described in the following sections. SDO Control (SDO1 and SDO2) The SDO bits enable the user to control the SDO output driver strength, disable the SDO output, or configure it as an open- drain driver. The strength of the SDO driver affects the timing of t12 and, when stronger, allows a faster clock cycle to be used. Note that when the SDO output is disabled the daisy-chain mode is also disabled. Table 10. SDO Control Bits SDO2 SDO1 Function 0 0 Full SDO driver 0 1 Weak SDO driver 1 0 SDO configured as open drain 1 1 Disable SDO output Daisy-Chain Control (DSY) DSY enables or disables daisy-chain mode. A 1 enables daisy- chain mode; a 0 disables it. When disabled, a readback request is accepted, SDO is automatically enabled, the DAC register contents of the relevant DAC are clocked out on SDO, and, when complete, SDO is disabled again. Hardware CLR Bit (HCLR) The default setting for the hardware CLR pin is to clear the registers and DAC output to zero code. A 1 in the HCLR bit clears the DAC outputs to midscale; a 0 clears them to zero scale. Active Clock Edge (SCLK) The default active clock edge is the falling edge. Write a 1 to this bit to clock data in on the rising edge; write a 0 to clock it in on the falling edge. DATA BITS CONTROL BITS C3 C2 C1 C0 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB0 (LSB) DB15 (MSB) Figure 39. 12-Bit Input Shift Register Contents CONTROL BITS 1 1 0 1 SDO1 SDO2 DSY HCLR SCLK X X X X X X X DB0 (LSB) DB15 (MSB) Figure 40. Control Register Loading Sequence |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |