Electronic Components Datasheet Search
  English  ▼

X  

AD5415 Datasheet(PDF) 23 Page - Analog Devices

Part # AD5415
Description  Dual 12-Bit, High Bandwidth, Multiplying DAC
PDF  27 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

AD5415 Datasheet(HTML) 23 Page - Analog Devices

Back Button AD5415 Datasheet HTML 19Page - Analog Devices AD5415 Datasheet HTML 20Page - Analog Devices AD5415 Datasheet HTML 21Page - Analog Devices AD5415 Datasheet HTML 22Page - Analog Devices AD5415 Datasheet HTML 23Page - Analog Devices AD5415 Datasheet HTML 24Page - Analog Devices AD5415 Datasheet HTML 25Page - Analog Devices AD5415 Datasheet HTML 26Page - Analog Devices AD5415 Datasheet HTML 27Page - Analog Devices  
Zoom Inzoom in Zoom Outzoom out
 23 / 27 page
background image
Data Sheet
AD5415
Rev. F | Page 23 of 27
80C51/80L51 to AD5415 Interface
A serial interface between the DAC and the 80C51 is shown in
Figure 45. TxD of the 80C51 drives SCLK of the DAC serial
interface, and RxD drives the serial data line, SDIN. P1.1 is a
bit-programmable pin on the serial port and is used to drive
SYNC. When data is to be transmitted to the switch, P1.1 is
taken low. The 80C51/80L51 only transmits data in 8-bit bytes;
therefore, only eight falling clock edges occur in the transmit
cycle. To load data correctly to the DAC, P1.1 is left low after
the first eight bits are transmitted, and a second write cycle is
initiated to transmit the second byte of data. Data on RxD is
clocked out of the microcontroller on the rising edge of TxD
and is valid on the falling edge of TxD. As a result, no glue logic
is required between the DAC and microcontroller interface.
P1.1 is taken high following the completion of this cycle. The
80C51 provides the LSB of the SBUF register as the first bit in
the data stream. The DAC input register requires the data with
the MSB as the first bit received. The transmit routine must take
this into account.
SCLK
TxD
80511
SYNC
P1.1
SDIN
RxD
1ADDITIONAL PINS OMITTED FOR CLARITY.
AD54151
Figure 45. 80C51/80L51 to AD5415 Interface
MC68HC11 to AD5415 Interface
Figure 46 is an example of a serial interface between the DAC and
the MC68HC11 microcontroller (Motorola). The serial peripheral
interface (SPI) on the MC68HC11 is configured for master mode
(MSTR) = 1, clock polarity bit (CPOL) = 0, and the clock phase
bit (CPHA) = 1. The SPI is configured by writing to the SPI control
register (SPCR); see the 68HC11 User Manual. SCK of the 68HC11
drives the SCLK of the DAC interface; the MOSI output drives
the serial data line (SDIN) of the DAC.
The SYNC signal is derived from a port line (PC7). When data
is transmitted to the AD5415, the SYNC line is taken low (PC7).
Data appearing on the MOSI output is valid on the falling edge of
SCK. Serial data from the 68HC11 is transmitted in 8-bit bytes with
only eight falling clock edges occurring in the transmit cycle. Data
is transmitted MSB first. To load data to the DAC, leave PC7 low
after the first eight bits are transferred and perform a second serial
write operation to the DAC. PC7 is taken high at the end of this
procedure.
SCLK
SCK
AD54151
SYNC
PC7
SDIN
MOSI
MC68HC111
1ADDITIONAL PINS OMITTED FOR CLARITY.
Figure 46. MC68HC11 to AD5415 Interface
If the user wants to verify the data previously written to the
input shift register, the SDO line can be connected to MISO of
the MC68HC11, and, with SYNC low, the shift register clocks
data out on the rising edges of SCLK.
MICROWIRE to AD5415 Interface
Figure 47 shows an interface between the DAC and any
MICROWIRE-compatible device. Serial data is shifted out on
the falling edge of the serial clock, SK, and is clocked into the
DAC input shift register on the rising edge of SK, which
corresponds to the falling edge of the DAC SCLK.
SCLK
SK
MICROWIRE1
SYNC
CS
SDIN
SO
AD54151
1ADDITIONAL PINS OMITTED FOR CLARITY.
Figure 47. MICROWIRE to AD5415 Interface
PIC16C6x/PIC16C7x to AD5415 Interface
The PIC16C6x/PIC16C7x (Microchip) synchronous serial port
(SSP) is configured as an SPI master with the clock polarity bit
(CKP) = 0. This is done by writing to the synchronous serial
port control register (SSPCON). In this example, the input/output
port RA1 is used to provide a SYNC signal and enable the serial
port of the DAC. This microcontroller transfers only eight bits
of data during each serial transfer operation; therefore, two
consecutive write operations are required. Figure 48 shows the
connection diagram.
SCLK
SCK/RC3
PIC16C6x/7x1
SYNC
RA1
SDIN
SDI/RC4
AD54151
1ADDITIONAL PINS OMITTED FOR CLARITY.
Figure 48. PIC16C6x/PIC16C7x to AD5415 Interface



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com