| Electronic Components Datasheet Search |
|
AD5415 Datasheet(PDF) 17 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
AD5415 Datasheet(HTML) 17 Page - Analog Devices |
|
17 / 27 page ![]() Data Sheet AD5415 Rev. F | Page 17 of 27 ADDING GAIN In applications where the output voltage must be greater than VIN, gain can be added with an additional external amplifier or it can be achieved in a single stage. Consider the effect of temperature coefficients of the thin film resistors of the DAC. Simply placing a resistor in series with the RFB resistor causes mismatches in the temperature coefficients, resulting in larger gain temperature coefficient errors. Instead, the circuit in Figure 37 shows the recommended method for increasing the gain of the circuit. R1, R2, and R3 can have similar temperature coefficients, but they need not match the temperature coefficients of the DAC. This approach is recommended in circuits where gains greater than 1 are required. Note that RFB ≫R2//R3andagainerrorpercentageof 100 × (R2//R3)/RFB must be taken into consideration. VDD RFBA IOUT1A IOUT2A C1 GND VDD VREFA NOTES 1. ADDITIONAL PINS OMITTED FOR CLARITY. 2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED IF A1 IS A HIGH SPEED AMPLIFIER. 12-BIT DAC VIN R1 R3 R2 VOUT R1 = R2R3 R2 + R3 GAIN = R2 + R3 R2 Figure 37. Increasing the Gain of the Current Output DAC DIVIDER OR PROGRAMMABLE GAIN ELEMENT Current steering DACs are very flexible and lend themselves to many applications. If this type of DAC is connected as the feedback element of an operational amplifier and RFB is used as the input resistor, as shown in Figure 38, the output voltage is inversely proportional to the digital input fraction, D. For D, which is equal to 1 − 2−n, the output voltage is VOUT = −VIN/D = −VIN/(1 − 2−n) VIN NOTES 1. ADDITIONAL PINS OMITTED FOR CLARITY. VREFA VDD VDD RFBA IOUT1A IOUT2A GND VOUT Figure 38. Current Steering DAC Used as a Divider or Programmable Gain Element As D is reduced, the output voltage increases. For small values of the digital fraction, D, it is important to ensure the amplifier does not saturate and the required accuracy is met. For example, an 8-bit DAC driven with the binary code 0x10 (0001 0000)—that is, 16 decimal—in the circuit of Figure 38 must cause the output voltage to be 16 times VIN. However, if the DAC has a linearity specification of ±0.5 LSB, D can have a weight in the range of 15.5/256 to 16.5/256, so that the possible output voltage is in the range of 15.5 VIN to 16.5 VIN—an error of 3%, even though the DAC itself has a maximum error of 0.2%. DAC leakage current is also a potential source of errors in divider circuits. The leakage current must be counterbalanced by an opposite current supplied from the operational amplifier through the DAC. Because only a fraction, D, of the current into the VREFA terminal is routed to the IOUT1A terminal, the output voltage changes as follows: Output Error Voltage Due to DAC Leakage = (Leakage × R)/D where R is the DAC resistance at the VREFA terminal. For a DAC leakage current of 10 nA, R = 10 kΩ, and a gain (that is, 1/D) of 16, the error voltage is 1.6 mV. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |