MAX11152 datasheet(3/33 Pages) MAXIM

3 / 33 page

Maxim Integrated │ 3

www.maximintegrated.com

Evaluates: MAX11150/MAX11152/

MAX11158/MAX11160/MAX11161/MAX11162/

MAX11163/MAX11168/MAX11169

MAX1115X/MAX1116X Family

Evaluation Kit

For Standalone Mode:

1) Verify that all jumpers are in their default positions for

the EV kit board (Table 2).

2) Connect the PC to the EV kit using a micro USB cable.

3) Connect the +20V adapter to the EV kit.

4) Start the EV kit software by opening its icon in the

Start | Programs menu. The EV kit software appears

in Figure 1.

5) The software should automatically connect to the

hardware and display

EV kit Hardware Connected

in the

Status bar. If it does not connect, then from the

Device menu, select Standalone and click Search

for USB Device. Then select Standalone again and

select a device in the list. Verify that the lower right

status bar indicates the EV kit hardware is

Connect-

ed.

For FPGA Mode (When Connected to a Zedboard):

1) Connect the Ethernet cable from the PC to the Zed-

Board and configure the Internet Protocol Version

4 (TCP/Ipv4) properties in the local area connec-

tion to IP address 192.168.1.2 and subnet mask to

255.255.255.0.

2) Verify that the ZedBoard SD card contains the Boot.

bin file for the MAX1115X/MAX1116X EV kit.

3) Connect the EV kit FMC connector to the ZedBoard

FMC connector. Gently press them together.

4) Verify that all jumpers are in their default positions for

the ZedBoard (Table 1) and EV kit board (Table 2).

5) Connect the 12V power supply to the ZedBoard.

Leave the Zedboard powered off.

6) Enable the ZedBoard power supply by sliding SW8 to

ON and connect the +20V adapter to the EV kit.

7) Start the EV kit software by opening its icon in the

Start | Programs menu. The EV kit software appears

as shown in Figure 1. From the

Device menu select

FPGA. Verify that the lower right status bar indicates

the EV Kit hardware is

Connected.

For Either Standalone or FPGA Mode:

1) Connect the positive terminal of the function genera-

tor to the AIN0+ (TP2) test point on the EV kit. Con-

nect the negative terminal of the function generator to

the AIN0- (TP1) test point on the EV kit.

2) Configure the signal source to generate a 1kHz,

1VP-P sinusoidal wave with +500mV offset.

3) Turn on the function generator.

4) In the

Configuration group, select Device to match

IC type, select

Channel 1 and then click Capture.

5) Click on the

Scope tab.

6) Check the

Remove DC Offset checkbox to remove

the DC component of the sampled data.

7) Click the

Capture button to start the data analysis.

The default sample size is 8192.

8) The EV kit software appears as shown in Figure 1.

9) Verify the frequency is approximately 1kHz is dis-

played on the right. The scope image has buttons in

the upper right corner that allow zooming in to detail.

Table 1. ZedBoard Jumper Settings

JUMPER

SHUNT POSITION

DESCRIPTION

J18

1-2

VDDIO set for 3.3V.

JP11

JP10

JP9

JP8

JP7

JP10

2-3

1-2

2-3

Boot from SD card

J12

—

SD card installed

J20

—

Connected to 12V wall adapter

SW8

OFF

ZedBoard power switch, OFF while connecting boards

MAX11152 Datasheet(PDF) 3 Page - Maxim Integrated Products

MAX11152 Datasheet(HTML) 3 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

Datasheet Download

Link URL