1 MSPS,12-Bit ADCs

Data Sheet

AD7475/AD7495

Rev. D

Document Feedback

Information furnished by Analog Devices is believed to be accurate and reliable. However, no

responsibilityisassumedbyAnalogDevicesforitsuse,norforanyinfringementsofpatentsorother

rightsofthirdpartiesthatmayresultfromitsuse.Specificationssubjecttochangewithoutnotice.No

license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

Trademarksandregisteredtrademarksarethepropertyoftheirrespectiveowners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Tel: 781.329.4700

©2018 Analog Devices, Inc. All rights reserved.

Technical Support

www.analog.com

FEATURES

Fast throughput rate: 1 MSPS

Low power

4.5 mW max at 1 MSPS with 3 V supplies

10.5 mW max at 1 MSPS with 5 V supplies

Wide input bandwidth: 68 dB SNR at 300 kHz input frequency

Flexible power/serial clock speed management

No pipeline delays

High speed serial interface

SPI-/QSPI™-/MICROWIRE-/DSP-compatible

On-board reference: 2.5 V (AD7495 only)

Standby mode: 1 µA max

8-lead MSOP and SOIC packages

APPLICATIONS

Battery-powered systems

Personal digital assistants

Medical instruments

Mobile communications

Instrumentation and control systems

Data acquisition systems

Optical sensors

GENERAL DESCRIPTION

The AD7475/AD74951 are 12-bit, high speed, low power,

successive-approximation ADCs that operate from a single

2.7 V to 5.25 V power supply with throughput rates up to 1 MSPS.

They contain a low noise, wide bandwidth track-and-hold

amplifier that can handle input frequencies above 1 MHz.

The conversion process and data acquisition are controlled

using CS and the serial clock, allowing the devices to interface

with microprocessors or DSPs. The input signal is sampled on

the falling edge of CS and conversion is initiated at this point.

The conversion time is determined by the SCLK frequency.

There are no pipeline delays associated with the device.

The AD7475/AD7495 use advanced design techniques to

achieve very low power dissipation at high throughput rates.

With 3 V supplies and a 1 MSPS throughput rate, the AD7475

consumes just 1.5 mA, while the AD7495 consumes 2 mA. With

5 V supplies and 1 MSPS, the current consumption is 2.1 mA

for the AD7475 and 2.6 mA for the AD7495.

The analog input range for the devices is 0 V to REF IN. The

2.5 V reference for the AD7475 is applied externally to the REF IN

pin, while the AD7495 has an on-board 2.5 V reference.

1

Protected by U.S. Patent No. 6,681,332

FUNCTIONAL BLOCK DIAGRAM

T/H

12-BIT

SUCCESSIVE

APPROXIMATION

ADC

AD7475

GND

SCLK

CS

CONTROL

LOGIC

SDATA

REF IN

T/H

12-BIT

SUCCESSIVE

APPROXIMATION

ADC

AD7495

GND

SCLK

CONTROL

LOGIC

SDATA

BUF

2.5V

REFERENCE

REF OUT

CS

Figure 1.

PRODUCT HIGHLIGHTS

1. The AD7475 offers 1 MSPS throughput rates with 4.5 mW

power consumption.

AD7475/AD7495 operate from a single 2.7 V to 5.25 V

connect directly to either 3 V or 5 V processor systems

3. Flexible power/serial clock speed management. The

conversion rate is determined by the serial clock, allowing

the conversion time to be reduced through the serial clock

speed increase. The devices also feature shutdown modes

to maximize power efficiency at lower throughput rates.

This allows the average power consumption to reduce while

not converting. Power consumption is 1 µA when in full

shutdown.

4. No pipeline delay. The devices feature a standard successive

approximation ADC with accurate control of the sampling

instant via a CS input and once-off conversion control.