| Electronic Components Datasheet Search |
|
LM5034 Datasheet(PDF) 22 Page - National Semiconductor (TI) |
|
|
|
|||||||||||||||||||||||||||||
LM5034 Datasheet(HTML) 22 Page - National Semiconductor (TI) |
|
22 / 29 page ![]() Applications Information (Continued) HICCUP MODE CURRENT LIMIT RESTART This circuit’s operation is described in the Functional De- scription. Also see Figure 20 and Figure 21. In the case of continuous current limit detection at both CS pins, the time required to reach the 2.55V RES pin threshold is: For example, if C RES = 0.1 µF the time t1 in Figure 21 is approximately 12.75 ms. In the case of continuous current limit detection at one CS pin only, the time to reach the 2.55V threshold is increased by a factor of four, or: t1=5.1x10 5 xC RES The time t2 in Figure 21 is set by the capacitor at each SS pin and the internal 1 µA current source, and is equal to: If C SS = 0.1 µF t2 is )150 ms. Time t3 is set by the internal 50 µA current source, and is equal to: The time t2 provides a periodic dwell time for the converter in the event of a sustained overload or short circuit. This results in lower average input current and lower power dissipated within the circuit components. It is recommended that the ratio of t2/(t1 + t3) be in the range of 5 to 10 to make good use of this feature. If the application requires no delay from the first detection of a current limit condition, so that t1 is effectively zero, the RES pin can be left open (no external capacitor). If it is desired to disable the hiccup mode current limit operation then the RES pin should be connected to ground. SOFT-START The capacitors at SS1 and SS2 determine the time required for each regulator’s output duty cycle to increase from zero to its final value for regulation. The minimum acceptable time is dependent on the output capacitance and the response of each feedback loop to the COMP pin. If the Soft-start time is too quick, the output could significantly overshoot its in- tended voltage before the feedback loop has a chance to regulate the PWM controller. After power is applied and V CC has passed its upper UVT threshold ()7.6V), the voltage at each SS pin ramps up as its external capacitor is charged up by an internal 50 µA current source (see Figure 3). The voltage at the COMP pins follow the SS pins. When both have reached )1.5V, PWM pulses appear at the driver outputs with very low duty cycle. The voltage at each SS pin continues to increase to )5.0V. The voltage at each COMP pin, and the PWM duty cycle, increase to the value required for regulation as determined by its feedback loop. The time t1 in Figure 3 is calculated from: With a 0.1 µF capacitor at SS, t1 is )3 ms. If the Hiccup Mode Current Limit Restart circuit activates due to repeated current limit detections at CS1 and/or CS2, both SS1 and SS2 are internally grounded (see the section on Hiccup Mode Current Limit Restart). After a short propaga- tion delay, the SS pins are released and the external SS pin capacitors are charged by internal 1 µA current sources. The slow charge rate provides a rest or dwell time for the con- verter power stage (t2 in Figure 21), reducing the average input current and component temperature rise while in an overload condition. When the voltage at the SS and COMP pins reach )1.5V, the first pulse out of either PWM compara- tor switches the internal SS pin current sources to 50 µA. The voltages at the SS and COMP pins then increase more quickly, increasing the duty cycle at the output drivers. The rest time t2 is the time required for SS to reach 1.5V: 20136831 FIGURE 30. Current Sense Using a Current Sense Transformer 20136832 FIGURE 31. Current Sense Using a Source Sense Resistor (R1) www.national.com 22 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |