| Electronic Components Datasheet Search |
|
LM5034 Datasheet(PDF) 16 Page - National Semiconductor (TI) |
|
|
|
|||||||||||||||||||||||||||||
LM5034 Datasheet(HTML) 16 Page - National Semiconductor (TI) |
|
16 / 29 page ![]() Cycle-by-Cycle Current Limit Each CS pin is designed to accept a signal representative of its transformer primary current. If the voltage at CS exceeds 0.5V the current sense comparator terminates the present main output driver (OUT pin) pulse. If the high current fault persists, the controller operates with constant peak switch current in a cycle-by-cycle current limit mode, and a Hiccup Mode Current Limit Restart cycle begins (see below). Each CS pin is internally connect to ground through a 30 Ω resistor during the main output off time to discharge external filter capacitance. The discharge device remains on for an additional 50 ns after the main output driver switches high to blank leading edge transients in the current sensing circuit. Discharging the CS pin filter each cycle and blanking leading edge spikes reduces the filter requirement which improves the current sense response time. The current sense comparators are fast and respond to short duration noise pulses. The external circuitry at each CS pin should include an R-C filter to suppress noise. Layout con- siderations are critical for the current sense filter and the sense resistor. Refer to the Applications Information section for PC board layout guidelines. Hiccup Mode Current Limit Restart If cycle-by-cycle current limiting continues in either or both controllers for a sufficient period of time, the Current Limit Restart circuit disables both regulators and initiates a soft- start sequence after a programmable delay. The duration of cycle-by-cycle current limiting before turn-off occurs is pro- grammed by the value of the external capacitor at the RES pin. The dwell time before output switching resumes is pro- grammed by the value of the Soft-start capacitor(s). The circuit is detailed in Figure 20 and the timing is shown in Figure 21. A description of this circuit’s operation is as fol- lows: a) No current limit detected: The 10 µA discharge current source at RES is enabled pulling the RES pin to ground. b) Current limit repeatedly detected at both CS inputs: The 20 µA current source at RES is enabled continuously to charge the RES pin capacitor as shown in Figure 21. The current limit comparators also terminate the PWM output pulses to provide a cycle-by-cycle current limiting. When the voltage on the RES capacitor reaches the 2.55V restart comparator threshold, the comparator sets the Restart Latch which produces the following restart sequence: • The SS1 and SS2 pin charging currents are reduced from 50µA to 1 µA, • An internal MOSFET is turned on to discharge the RES pin capacitor. • The internal MOSFETs at SS1 and SS2 are turned on to discharge the Soft-start capacitors. • COMP1 and COMP2 follow SS1 and SS2 respectively and reduce the PWM duty cycles to zero • When the voltages at the SS pins fall below 200mV, the internal MOSFETs at the SS pins are turned off allowing the SS pins to be charged by the 1µA current sources. • When either SS pin reaches )1.5V its PWM controller produces the first pulse of a soft-start sequence which resets the Restart Latch. The SS charging currents are increased to 50 µA and the soft-start sequence continues at the normal rate. If the overload condition still exists, the voltage at RES begins to increase again and repeat the restart cycle as shown in Figure 21. If the overload condition has been cleared, the RES pin is held at ground by the 10 µA current source. c) Current limit repeatedly detected at one of the two CS inputs: In this condition the RES pin capacitor is charged by the 20 µA current source once each clock cycle of the current limited regulator (CLK1 or CLK2), and discharged by the 10 µA current source once each clock cycle of the unaffected regulator. The voltage at the RES pin increases one fourth as fast as in case b) described above. The current limited regulator operates in a cycle-by-cycle current limit mode until the voltage at RES reaches the 2.55V threshold. When the Restart Comparator output switches high the Restart Latch is set, both SS pin capacitors are discharged to disable the regulator channels, and a restart sequence begins as de- scribed in case b) above. To determine the value of the RES pin capacitor, see the Applications Information section. www.national.com 16 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |