DRA752ABC datasheet(12/443 Pages) TI2

12 / 443 page

DRA756, DRA755, DRA754, DRA752

DRA751, DRA750, DRA746, DRA745, DRA744

SPRS950F – DECEMBER 2015 – REVISED MAY 2019

www.ti.com

Submit Documentation Feedback

Product Folder Links: DRA756 DRA755 DRA754 DRA752 DRA751 DRA750 DRA746 DRA745 DRA744

Terminal Configuration and Functions

–

O = Output

–

IO = Input or Output

–

D = Open drain

–

DS = Differential Signaling

–

A = Analog

–

PWR = Power

–

GND = Ground

–

CAP = LDO Capacitor

7. BALL RESET STATE: The state of the terminal at power-on reset:

–

drive 0 (OFF): The buffer drives VOL (pulldown or pullup resistor not activated)

–

drive 1 (OFF): The buffer drives VOH (pulldown or pullup resistor not activated)

–

OFF: High-impedance

–

PD: High-impedance with an active pulldown resistor

–

PU: High-impedance with an active pullup resistor

–

An empty box means Not Applicable

8. BALL RESET REL. STATE: The state of the terminal at the deactivation of the rstoutn signal (also

mapped to the PRCM SYS_WARM_OUT_RST signal)

–

drive 0 (OFF): The buffer drives VOL (pulldown or pullup resistor not activated)

–

drive clk (OFF): The buffer drives a toggling clock (pulldown or pullup resistor not activated)

–

drive 1 (OFF): The buffer drives VOH (pulldown or pullup resistor not activated)

–

OFF: High-impedance

–

PD: High-impedance with an active pulldown resistor

–

PU: High-impedance with an active pullup resistor

–

An empty box means Not Applicable

NOTE

For more information on the CORE_PWRON_RET_RST reset signal and its reset sources,

see the Power Reset and Clock Management / PRCM Reset Management Functional

Description section of the Device TRM.

9. BALL RESET REL. MUXMODE: This muxmode is automatically configured at the release of the

rstoutn signal (also mapped to the PRCM SYS_WARM_OUT_RST signal).

An empty box means Not Applicable.

10. IO VOLTAGE VALUE: This column describes the IO voltage value (VDDS supply).

An empty box means Not Applicable.

11. POWER: The voltage supply that powers the terminal IO buffers.

An empty box means Not Applicable.

12. HYS: Indicates if the input buffer is with hysteresis:

–

Yes: With hysteresis

–

No: Without hysteresis

–

An empty box: Not Applicable

NOTE

For more information, see the hysteresis values in Section 5.7, Electrical Characteristics.

13. BUFFER TYPE: Drive strength of the associated output buffer.

An empty box means Not Applicable.

DRA752ABC Datasheet(PDF) 12 Page - Texas Instruments

DRA752ABC Datasheet(HTML) 12 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL