TAS5705PAP datasheet(22/71 Pages) TI

22 / 71 page

DEVICE PROTECTION SYSTEM

Overcurrent (OC) Protection With Current Limiting

Overtemperature Protection

Undervoltage Protection (UVP) and Power-On

DEVICE RESET

TAS5705

SLOS549 – JUNE 2008 ...................................................................................................................................................................................................... www.ti.com

The TAS5705 contains advanced protection circuitry carefully designed to facilitate system integration and ease

of use, as well as to safeguard the device from permanent failure due to a wide range of fault conditions such as

short circuits, overtemperature, and undervoltage. The TAS5705 responds to a fault by immediately setting the

power stage in a high-impedance (Hi-Z) state and asserting the FAULT pin low. The device automatically

recovers when the fault condition has been removed.

The device has independent, fast-reacting current detectors on all high-side and low-side power-stage FETs. The

detector outputs are closely monitored by two protection systems. The first protection system controls the power

stage in order to prevent the output current further increasing, i.e., it performs a cycle-by-cycle current-limiting

function, rather than prematurely shutting down during combinations of high-level music transients and extreme

speaker load impedance drops. If the high-current condition situation persists, i.e., the power stage is being

overloaded, a second protection system triggers a latching shutdown, resulting in the power stage being set in

the high-impedance (Hi-Z) state. The device returns to normal operation once the fault condition (i.e., a short

circuit on the output) is removed. Current limiting and overcurrent protection are not independent for half-bridges

A and B and, respectively, C and D. That is, if the bridge-tied load between half-bridges A and B causes an

overcurrent fault, half-bridges A, B, C, and D are shut down.

The overcurrent protection threshold is set by a resistor to ground from the OC_ADJ pin. A value of 22 k

Ω will

result in an overcurrent threshold of 4.5 A. This resistor value should not be changed.

The TAS5705 has a two-level temperature-protection system that asserts an active-high warning signal (OTW)

when the device junction temperature exceeds 125°C (nominal) and, if the device junction temperature exceeds

150°C (nominal), the device is put into thermal shutdown, resulting in all half-bridge outputs being set in the

high-impedance (Hi-Z) state and FAULT being asserted low. OTE is latched in this case. To clear the OTE latch,

RESET must be asserted. Thereafter, the device resumes normal operation.

Reset (POR)

The UVP and POR circuits of the TAS5705 fully protect the device in any power-up/down and brownout situation.

While powering up, the POR circuit resets the overload circuit (OLP) and ensures that all circuits are fully

operational when the GVDD_XY and VREG supply voltages reach 5.7 V (typical) and 2.7 V, respectively.

Although GVDD_XY and VREG are independently monitored, a supply voltage drop below the UVP threshold on

VREG or either GVDD_XY pin results in all half-bridge outputs immediately being set in the high-impedance

(Hi-Z) state and FAULT being asserted low. The device automatically resumes operation when all supply

voltages have increased above the UVP threshold.

One reset pin is provided for control of half-bridges A/B/C/D. When RESET is asserted low, all four power-stage

FETs in half-bridges A, B, C, and D are forced into a high-impedance (Hi-Z) state.

In BTL modes, to accommodate bootstrap charging prior to switching start, asserting the reset input low enables

weak pulldown of the half-bridge outputs. In the SE mode, the weak pulldowns are not enabled, and it is

therefore recommended to ensure bootstrap capacitor charging by providing a low pulse on the PWM inputs

when reset is asserted high.

Asserting the reset input low removes any fault information to be signaled on the FAULT output, i.e., FAULT is

forced high.

A rising-edge transition on the reset input allows the device to resume operation after an overcurrent fault.

Submit Documentation Feedback

Product Folder Link(s): TAS5705

TAS5705PAP Datasheet(PDF) 22 Page - Texas Instruments

TAS5705PAP Datasheet(HTML) 22 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71

Datasheet Download

Link URL