| Electronic Components Datasheet Search |
|
AD5750 Datasheet(PDF) 23 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
AD5750 Datasheet(HTML) 23 Page - Analog Devices |
|
23 / 25 page ![]() Preliminary Technical Data AD5750 Rev. PrC | Page 23 of 25 the internal current sense resistor to be 14.7K, giving a nominal 2% overrange capability. This feature is available in the 0-20ma, 4-20ma, +/-20ma current ranges. The stability of the output current value over temperature is dependent on the stability of the value of RSET. As a method of improving the stability of the output current over temperature an external low drift resistor can be connected to the RSET1 & RSET2 pins of the AD5750 to be used instead of the internal resistor RSET. The external resistor is selected via the input register. If the external resistor option is not used the RSET1 and RSET2 pins should be left floating. PROGRAMMABLE OVER-RANGE MODES The AD5750 contains an over range mode for most of the available ranges. In voltage mode the over-range is typically 20% and in current mode the over-range is typically 2%. The overranges are selected by configuring R3, R1, R1, R0 bits/pins accordingly. In voltage mode the overranges are typically 20% providing programmable output ranges of 0-6v, 0-12v, +/-6v and +/-12v. The 0-4.096v analog input remains the same. In current mode the overranges are typically 2%. In current mode the overrange capability is only available on 3 ranges, 0- 20ma, 0-24ma, 4-20ma. For these ranges the analog input will also vary, according to the table below. Over Range Analog Input 0-20.4ma 0.075v – 4.096v 3.92-20.4ma 0.06v-4.096v 0-24.5ma 0.065-4.096v For example, in 0-20.4ma range, an analog input of 0.075v will output 0ma and 4.096v will output full scale 20.4ma. PACKET ERROR CHECKING To verify that data has been received correctly in noisy environments, the AD5750 offers the option of error checking based on an 8-bit (CRC-8) cyclic redundancy check. The device controlling the AD5750 should generate an 8-bit frame check sequence using the polynomial C(x) = x8 + x2 + x1 +1. This is added to the end of the data word, and 24 data bits are sent to the AD5750 before taking SYNC high. If the AD5750 sees a 24-bit data frame, it will perform the error check when SYNC goes high. If the check is valid, then the data will be written to the selected register. If the error check fails, the FAULT will go high and bit D4 of the Status Register is set. After reading this register, this error flag is cleared automatically and PEC goes high again. SYNC SCLK DIN 16-BIT DATA TRANSFER - NO ERROR CHECKING SYNC SCLK DIN MSB D15 LSB D0 MSB D23 LSB D8 D7 D0 UPDATE ON SYNC HIGH UPDATE AFTER SYNC HIGH ONLY IF ERROR CHECK PASSED 16-BIT DATA 16 BIT DATA 16-BIT DATA TRANSFER WITH ERROR CHECKING 8-BIT FCS PEC PEC GOES LOW IF ERROR CHECK FAILS Figure 13. PEC Error Checking Timing |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |