| Electronic Components Datasheet Search |
|
LTC1771 Datasheet(PDF) 8 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LTC1771 Datasheet(HTML) 8 Page - Linear Technology |
|
8 / 16 page ![]() 8 LTC1771 Power MOSFET Selection An external P-channel power MOSFET must be selected for use with the LTC1771. The main selection criteria for the power MOSFET are the threshold voltage VGS(TH) and the “on” resistance RDS(ON), reverse transfer capacitance and total gate charge. Since the LTC1771 can operate down to input voltages as low as 2.8V, a sublogic level threshold MOSFET (RDS(ON) guaranteed at VGS = 2.5V) is required for applications that work close to this voltage. When these MOSFETs are used, make sure that the input supply to the LTC1771 is less than the absolute maximum VGS rating (typically 12V), as the MOSFET gate will see the full supply voltage. The required RDS(ON) of the MOSFET is governed by its allowable power dissipation. For applications that may operate the LTC1771 in dropout, i.e. 100% duty cycle, at its worst case the required RDS(ON) is given by: R P I DS ON P OUT MAX P () () = () +() 2 1 δ where PP is the allowable power dissipation and δP is the temperature dependency of RDS(ON). (1 + δP) is generally given for a MOSFET in the form of a normalized RDS(ON) vs temperature curve, but = 0.005/ °C can be used as an approximation for low voltage MOSFETs. In applications where the maximum duty cycle is less than 100% and the LTC1771 is in continuous mode, the RDS(ON) is governed by: R P DC I DC VV VV DS ON P OUT P OUT D IN D () = () + () = + + 2 1 δ where DC is the maximum operating duty cycle of the LTC1771. Catch Diode Selection The catch diode carries load current during the off-time. The average diode current is therefore dependent on the P-channel switch duty cycle. At high input voltages the diode conducts most of the time. As VIN approaches VOUT the diode conducts only a small fraction of the time. The most stressful condition for the diode is when the output is short-circuited. Under this condition, the diode must safely handle IPEAK at close to 100% duty cycle. To maximize both low and high current efficiencies, a fast switching diode with low forward drop and low reverse leakage should be used. Low reverse leakage current is critical to maximize low current efficiency since the leak- age can potentially exceed the magnitude of the LTC1771 supply current. Low forward drop is critical for high current efficiency since loss is proportional to forward drop. The effect of reverse leakage and forward drop on no- load supply current and efficiency for various Schottky diodes is shown in Table 1. As can be seen, these are conflicting parameters and the user must weigh the importance of each spec in choosing the best diode for the application. Table 1. Effect of Catch Diode on Performance LEAKAGE NO-LOAD EFFICIENCY DIODE (VR = 3.3V) VF @ 1A SUPPLY CURRENT AT 10V/1A MBR0540 0.25 µA 0.50V 10.4 µA 86.3% UPS5817 2.8 µA 0.41V 11.8 µA 88.2% MBR0520 3.7 µA 0.36V 12.2 µA 88.4% MBRS120T3 4.4 µA 0.43V 12.2 µA 87.9% MBRM120LT3 8.3 µA 0.32V 14.0 µA 89.4% MBRS320 19.7 µA 0.29V 20.0 µA 89.8% CIN and COUT Selection At higher load currents, when the inductor current is continuous, the source current of the P-channel MOSFET is a square wave of duty cycle VOUT/VIN. To prevent large voltage transients, a low ESR input capacitor sized for the maximum RMS current must be used. The maximum capacitor current is given by: C IV V V V IN MAX OUT IN OUT IN required IRMS = − () []12/ This formula has a maximum at VIN = 2VOUT, where IRMS = IOUT/2. This simple worst-case condition is com- monly used for design because even significant deviations do not offer much relief. Note that capacitor manufacturer’s APPLICATIO S I FOR ATIO |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |