| Electronic Components Datasheet Search |
|
LTC1771 Datasheet(PDF) 12 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LTC1771 Datasheet(HTML) 12 Page - Linear Technology |
|
12 / 16 page ![]() 12 LTC1771 2. Is the 0.1 µF input decoupling capacitor closely con- nected between VIN (Pin 6) and ground (Pin 4)? This capacitor carries the high frequency peak currents. 3. Does the VFB pin connect directly to the feedback resistors? The resistive divider R1 and R2 must be connected between the (+) plate of COUT and signal ground. Locate the feedback resistors right next to the LTC1771. The VFB line should not be routed close to any nodes with high slew rates. 4. Is the 1000pF decoupling capacitor for the current sense resistor connected as close as possible to Pins 6 and 7? Ensure accurate current sensing with Kelvin connections to the sense resistor. 5. Is the (+) plate of CIN closely connected to the sense resistor ? This capacitor provides the AC current to the MOSFET. 6. Are the signal and power grounds segregated? The signal ground consists of the (–) plate of COUT, Pin 4 of the LTC1771 and the resistive divider. The power ground consists of the Schottky diode anode and the (–) plate of CIN which should have as short lead lengths as possible. 7. Keep the switching node (SW) and the gate node (PGATE) away from sensitive small signal nodes, espe- cially the voltage sensing feedback pin (VFB), and mini- mize their PC trace area. Design Example As a design example, assume VIN = 10V (nominal), VIN = 15V(MAX), VOUT = 3.3V, and IMAX = 2A. With this informa- tion, we can easily calculate all the important components. RSENSE = 100mV/2A = 0.05Ω To optimize low current efficiency, MODE pin is tied to VIN to enable Burst Mode operation, thus the minimum induc- tance necessary is: LMIN = 70µH(3.3V + 0.5)(0.05Ω) = 13.3µH 15 µH is chosen for the application. ∆= + = Is VV H A L 35 33 05 15 089 . .. . µ µ For the feedback resistors, choose R1 = 1M to minimize supply current. R2 can then be calculated to be: R2 = (VOUT/1.23 – 1) • R1 = 1.68M Assume that the MOSFET dissipation is to be limited to PP = 0.25W. If TA = 70°C and the thermal resistance of the MOSFET is 83 °C/W, then the junction temperatures will be 91°C and δP = 0.33. The required RDS(ON) for the MOSFET can now be calculated: P W VV VV A - Channel RDS(ON) = + + () ( ) = 025 33 05 10 0 5 21 33 0 130 2 . .. . . . Ω Since the gate of the MOSFET will see the full input voltage, a MOSFET must be selected whose VGS(MAX) > 15V. A P-channel MOSFET that meets both the VGS(MAX) and RDS(ON) requirement is the Si6447DQ. The most stringent requirement for the Schottky diode occurs when VOUT = 0V (i.e., short circuit) at maximum VIN. In this case the worst-case dissipation rises to: PI V V VV SC AVG D IN IN D D = () + () Figure 5. LTC1771 Layout Diagram APPLICATIO S I FOR ATIO RUN/SS ITH VFB GND VOUT RITH CITH CFF 0.1 µF Q1 D1 R2 R1 1 2 3 4 8 7 6 5 1771 F05 CSS CIN MODE MODE SENSE VIN PGATE LTC1771 BOLD LINES INDICATE HIGH CURRENT PATHS + COUT L |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |