| Electronic Components Datasheet Search |
|
LTC1771 Datasheet(PDF) 9 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LTC1771 Datasheet(HTML) 9 Page - Linear Technology |
|
9 / 16 page ![]() 9 LTC1771 ripple current ratings are often based on 2000 hours of life. This makes it advisable to further derate the capacitor, or to choose a capacitor rated at a higher temperature than required. Do not underspecify this component. An addi- tional 0.1 µF ceramic capacitor is also helpful on VIN for high frequency decoupling. The selection of COUT is driven by the required effective series resistance (ESR). Typically, once the ESR require- ment is satisfied, the capacitance is adequate for filtering. The output ripple ( ∆VOUT) in continuous mode is approxi- mated by: ∆≈ + V I ESR fC OUT RIPPLE OUT 1 8 where f is the operating frequency, COUT is the output capacitance and IRIPPLE is the ripple current in the inductor. For output ripple less than 100mV, assure COUT required ESR is <2RSENSE. The first condition relates to the ripple current into the ESR of the output capacitance while the second term guaran- tees that the output capacitance does not significantly discharge during the operating frequency period due to ripple current. The choice of using smaller output capaci- tance increases the ripple voltage due to the discharging term but can be compensated for by using capacitors of very low ESR to maintain the ripple voltage at or below 50mV. The ITH pin OPTI-LOOP TM compensation compo- nents can be optimized to provide stable, high perfor- mance transient response regardless of the output capacitors selected. When running into dropout, extra input and output capaci- tance may be necessary for optimal performance due to the drop in frequency as the duty cycle approaches 100%. Compare Figure 1 to the low dropout regulators shown in the Typical Applications section for recommended CIN, COUT, CFF and CC values for low dropout regulators vs regulators not requiring low dropout. Manufacturers such as Nichicon, United Chemicon and Sanyo should be considered for high performance through- hole capacitors. The OS-CON semiconductor dielectric capacitor available from Sanyo has the lowest ESR for its size of any aluminum electrolytic at a somewhat higher price. Typically once the ESR requirement is satisfied, the RMS current rating generally far exceeds the IRIPPLE(P-P) requirement. In surface mount applications multiple capacitors may have to be paralleled to meet the ESR or RMS current handling requirements of the application. Aluminum electrolytics and dry tantalum capacitors are both available in surface mount configurations. In case of tantalum, it is critical that the capacitors are surge tested for use in switching power supplies. An excellent choice is the AVX TPS, AVX TPSV and KEMET T510 series of surface mount tantalums, available in case heights ranging from 2mm to 4mm. Other capacitor types include Sanyo OS-CON, Sanyo POSCAP, Nichicon PL series and Panasonic SP. Efficiency Considerations The efficiency of a switching regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual losses to determine what is limiting efficiency and which change would produce the most improvement. Efficiency can be expressed as: Efficiency = 100% – (L1 + L2 +L3 + ...) where L1, L2, etc. are the individual losses as a percentage of input power. Although all dissipative elements in the circuit produce losses, four main sources usually account for most of the losses in the LTC1771 circuits: the LTC1771 DC bias current, MOSFET gate charge current, I2R losses and catch diode losses. 1. The DC bias current is 9 µA at no load and increases proportionally with load up to a constant 150 µA during continuous mode. This bias current is so small that this loss is negligible at loads above a milliamp but at no load accounts for nearly all of the loss. 2. The MOSFET gate charge current results from switch- ing the gate capacitance of the power MOSFET switch. Each time the gate is switched from high to low to high again, a packet of charge dQ moves from VIN to ground. The resulting dQ/dt is the current out of VIN which is typically much larger than the DC bias current. In OPTI-LOOP is a trademark of Linear Technology Corporation. APPLICATIO S I FOR ATIO |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |