| Electronic Components Datasheet Search |
|
TLV986 Datasheet(PDF) 14 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TLV986 Datasheet(HTML) 14 Page - Texas Instruments |
|
14 / 20 page ![]() TLV986 3-V, 10-BIT, 12.5 MSPS, AREA CCD SENSOR PROCESSOR SLAS228 – JULY 1999 14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PRINCIPLES OF OPERATION internal timing Operating the CDS requires signals SR and SV as previously explained. The user needs to synchronize the SR and SV clocks with the CCD signal waveform. The output of the ADC is read out to external circuitry by the ADCCLK signal that is also used internally to control both ADC and PGA operations. It is necessary that the positive half cycle of the ADCCLK signal always falls in between two adjacent SV pulses as shown in Figure 1. The user can then fine tune the ADCCLK timing in relation to the CDS timing to achieve optimal performance. The TLV986 has direct access to the CDS and PGA internal clocks through the TPP and TPM terminal. The TPP and TPM assist the user in timing alignment. See Test Register Description for details. The CLAMP signal activates the input clamping and the OBCLP signal activates auto optical black and offset correction. input blanking function During some period of operation, large input transients may occur at the TLV986’s input, saturating the input circuits and causing long recovery time. To prevent the circuit saturation, the TLV986 includes an input blanking function that blocks the input signals by disabling the CDS operation whenever the BLKG input is pulled low. 3-wire serial interface A simple 3-wire (SCLK, SDIN, and CS) serial interface is provided to allow writing to the internal registers of the TLV986. The serial clock SCLK can be run at a maximum speed of 40 MHz. The serial data SDIN is 16 bits long. After two leading null bits, there are four address bits for which internal register is to be updated; the following ten bits are the data to be written to the register. To enable the serial port, the CS pin must be held low. The data transfer is initiated by the incoming SCLK after the CS falls. device reset When the reset (terminal 29) is pulled low, all internal registers are set to their default values. The device also resets itself when it is first powered on. In addition, the TLV986 has a software-reset function that resets the device when writing a control bit to the control register. See Register Definition section for the register default values. device reset When the reset (terminal 29) is pulled low, all internal registers are set to their default values. The device also resets itself when it is first powered on. In addition, the TLV986 has a software-reset function that resets the device when writing a control bit to the control register. See Register Definition section for the register default values. power-down mode (standby) The TLV986 has both hardware and software power–down modes. Pulling the STBY (terminal 30) low puts the device in the low-power standby mode. Total supply current drops to ~0.6 mA. Setting a power-down control bit in the control register can also activate the power-down mode. The user can still program all internal registers during the power-down mode. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |