| Electronic Components Datasheet Search |
|
SP6669 Datasheet(PDF) 7 Page - Exar Corporation |
|
|
|||||||||||||||||||||||||||||
SP6669 Datasheet(HTML) 7 Page - Exar Corporation |
|
7 / 10 page ![]() THEORY OF OPERATION Rev G – 12/02/2008 SP6669 1.5MHz 0.6A Sync. Step Down Converter © 2008 Exar Corporation 7/10 Detailed Description Applications The typical application circuit of the adjustable output voltage option and the fixed output voltage option are shown below. Fig. 18: Adjustable Output Voltage Version Typical Application Circuit Fig. 19: Fixed Output Voltage Version Typical Application Circuit Inductor Selection Inductor ripple current and core saturation are two factors considered to select the inductor value. Eq. 1: ⎟⎟ ⎠ ⎞ ⎜⎜ ⎝ ⎛ − ⋅ = Δ IN OUT OUT L V V V L f I 1 1 Equation 1 shows the inductor ripple current as a function of the frequency, inductance, VIN and VOUT. It is recommended to set the ripple current to 40% of the maximum load current. A low ESR inductor is preferred. CIN and COUT Selection A low ESR input capacitor can prevent large voltage transients at VIN. The RMS current rating of the input capacitor is required to be larger than IRMS calculated by: Eq. 2: () IN OUT IN OUT OMAX RMS V V V V I I − ≅ The ESR rating of the capacitor is an important parameter to select COUT. The output ripple VOUT is determined by: Eq. 3: ⎟⎟ ⎠ ⎞ ⎜⎜ ⎝ ⎛ ⋅ ⋅ + Δ ≅ Δ OUT L OUT C f ESR I V 8 1 Higher values, lower cost ceramic capacitors are now available in smaller sizes. These capacitors have high ripple currents, high voltage ratings and low ESR that makes them ideal for switching regulator applications. As COUT does not affect the internal control loop stability, its value can be optimized to balance very low output ripple and circuit size. It is recommended to use an X5R or X7R rated capacitors which have the best temperature and voltage characteristics of all the ceramics for a given value and size. Output Voltage – Adjustable Version The adjustable output voltage version is determined by: Eq. 4: ⎟⎟ ⎠ ⎞ ⎜⎜ ⎝ ⎛ + ⋅ = 1 2 1 6 . 0 R R V V OUT Thermal Considerations Allthough the SP6669 has an on board over temperature circuitry, the total power dissipation it can support is based on the package thermal capabilities. The formula to ensure safe operation is given in note 1. PCB Layout The following PCB layout guidelines should be taken into account to ensure proper operation and performance of the SP6669: 1- The GND, SW and VIN traces should be kept short, direct and wide. 2- VFB pin must be connected directly to the feedback resistors. The resistor divider network must be connected in parallel to the COUT capacitor. 3- The input capacitor CIN must be kept as close as possible to the VIN pin. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |