PCF2119FUSLASH2SLASHF2 datasheet(63/79 Pages) NXP

63 / 79 page

PCF2119X_5

Product data sheet

Rev. 05 — 13 August 2009

63 of 79

NXP Semiconductors

PCF2119x

LCD controllers/drivers

[1]

X = don’t care.

[2]

SDA is left at high-impedance by the microcontroller during the read acknowledge.

Write_data to DDRAM

writes ‘S’

DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack

PHILIPS

010100111

optional l2C-bus STOP

PHILIPS

I2C-bus start

PHILIPS

slave address for write

SA6 SA5 SA4 SA3 SA2 SA1 SA0 R/WAck

PHILIPS

011101001

control byte

Ack

PHILIPS

100000001

Return_home

sets DDRAM address 0 in address counter

(also returns shifted display to original

position; DDRAM contents unchanged); this

instruction does not update the data register

DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack

PHILIPS

000000101

I2C-bus start

PHILIPS

slave address for read

during the acknowledge cycle the content of

the data register is loaded into the internal

I2C-bus interface to be shifted out; in the

previous instruction neither a ‘set address’

nor a Read_data has been performed;

therefore the content of the data register

was unknown; bit R/W has to be set to logic

1 while still in I2C-write mode

SA6 SA5 SA4 SA3 SA2 SA1 SA0 R/WAck

PHILIPS

011101011

control byte for read

DDRAM content will be read from following

instructions

Ack

PHILIPS

011000001

Read_data: 8

× SCL + master acknowledge[2]

× SCL; content loaded into interface

during previous acknowledge cycle is

shifted out over SDA; MSB is DB7; during

master acknowledge content of DDRAM

address 01 is loaded into the I2C-bus

interface

DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack

PHILIPS

XXXXXXXX0

Read_data: 8

× SCL + master acknowledge[2]

× SCL; code of letter ‘H’ is read ﬁrst;

during master acknowledge code of ‘I’ is

loaded into the I2C-bus interface

DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack

PHILIPS

010010000

Read_data: 8

× SCL + no master acknowledge[2]

no master acknowledge; after the content of

the I2C-bus interface register is shifted out

no internal action is performed; no new data

is loaded to the interface register, data

not incremented and cursor is not shifted

DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack

PHILIPS

010010011

I2C-bus STOP

PHILIPS

Table 42.

Example of I2C-bus operation; 1-line display (using external reset, assuming pin SA0 = VSS)[1] …continued

Step

I2C-bus byte

Display

Operation

PCF2119FU/2/F2 Datasheet(PDF) 63 Page - NXP Semiconductors

PCF2119FU/2/F2 Datasheet(HTML) 63 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79

Datasheet Download

Link URL