ATmega324P datasheet(160/377 Pages) ATMEL

160 / 377 page

160

7674F–AVR–09/09

ATmega164P/324P/644P

15.11.8

TIFR2 – Timer/Counter2 Interrupt Flag Register

• Bit 2 – OCF2B: Output Compare Flag 2 B

The OCF2B bit is set (one) when a compare match occurs between the Timer/Counter2 and the

data in OCR2B – Output Compare Register2. OCF2B is cleared by hardware when executing

the corresponding interrupt handling vector. Alternatively, OCF2B is cleared by writing a logic

one to the flag. When the I-bit in SREG, OCIE2B (Timer/Counter2 Compare match Interrupt

Enable), and OCF2B are set (one), the Timer/Counter2 Compare match Interrupt is executed.

• Bit 1 – OCF2A: Output Compare Flag 2 A

The OCF2A bit is set (one) when a compare match occurs between the Timer/Counter2 and the

data in OCR2A – Output Compare Register2. OCF2A is cleared by hardware when executing

the corresponding interrupt handling vector. Alternatively, OCF2A is cleared by writing a logic

one to the flag. When the I-bit in SREG, OCIE2A (Timer/Counter2 Compare match Interrupt

Enable), and OCF2A are set (one), the Timer/Counter2 Compare match Interrupt is executed.

• Bit 0 – TOV2: Timer/Counter2 Overflow Flag

The TOV2 bit is set (one) when an overflow occurs in Timer/Counter2. TOV2 is cleared by hard-

ware when executing the corresponding interrupt handling vector. Alternatively, TOV2 is cleared

by writing a logic one to the flag. When the SREG I-bit, TOIE2A (Timer/Counter2 Overflow Inter-

rupt Enable), and TOV2 are set (one), the Timer/Counter2 Overflow interrupt is executed. In

PWM mode, this bit is set when Timer/Counter2 changes counting direction at 0x00.

15.11.9

GTCCR – General Timer/Counter Control Register

• Bit 1 – PSRASY: Prescaler Reset Timer/Counter2

When this bit is one, the Timer/Counter2 prescaler will be reset. This bit is normally cleared

immediately by hardware. If the bit is written when Timer/Counter2 is operating in asynchronous

mode, the bit will remain one until the prescaler has been reset. The bit will not be cleared by

hardware if the TSM bit is set. Refer to the description of the “Bit 7 – TSM: Timer/Counter Syn-

chronization Mode” on page 136 for a description of the Timer/Counter Synchronization mode.

Bit

76543210

0x17 (0x37)

–––––

OCF2B

OCF2A

TOV2

TIFR2

Read/Write

RRRRR

R/W

Initial Value

00000000

Bit

0x23 (0x43)

TSM

–

PSRASY

PSRSYNC

GTCCR

Read/Write

R/W

Initial Value

ATmega324P Datasheet(PDF) 160 Page - ATMEL Corporation

ATmega324P Datasheet(HTML) 160 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL