ATmega88 datasheet(154/340 Pages) ATMEL

154 / 340 page

154

7530H–AVR–02/09

ATmega48/88/168 Automotive

15.9.2

Asynchronous Status Register – ASSR

• Bit 6 – EXCLK: Enable External Clock Input

When EXCLK is written to one, and asynchronous clock is selected, the external clock input buf-

fer is enabled and an external clock can be input on Timer Oscillator 1 (TOSC1) pin instead of a

32 kHz crystal. Writing to EXCLK should be done before asynchronous operation is selected.

Note that the crystal Oscillator will only run when this bit is zero.

• Bit 5 – AS2: Asynchronous Timer/Counter2

When AS2 is written to zero, Timer/Counter2 is clocked from the I/O clock, clk

I/O. When AS2 is

written to one, Timer/Counter2 is clocked from a crystal Oscillator connected to the Timer Oscil-

lator 1 (TOSC1) pin. When the value of AS2 is changed, the contents of TCNT2, OCR2A,

OCR2B, TCCR2A and TCCR2B might be corrupted.

• Bit 4 – TCN2UB: Timer/Counter2 Update Busy

When Timer/Counter2 operates asynchronously and TCNT2 is written, this bit becomes set.

When TCNT2 has been updated from the temporary storage register, this bit is cleared by hard-

ware. A logical zero in this bit indicates that TCNT2 is ready to be updated with a new value.

• Bit 3 – OCR2AUB: Output Compare Register2 Update Busy

When Timer/Counter2 operates asynchronously and OCR2A is written, this bit becomes set.

When OCR2A has been updated from the temporary storage register, this bit is cleared by hard-

ware. A logical zero in this bit indicates that OCR2A is ready to be updated with a new value.

• Bit 2 – OCR2BUB: Output Compare Register2 Update Busy

When Timer/Counter2 operates asynchronously and OCR2B is written, this bit becomes set.

When OCR2B has been updated from the temporary storage register, this bit is cleared by hard-

ware. A logical zero in this bit indicates that OCR2B is ready to be updated with a new value.

• Bit 1 – TCR2AUB: Timer/Counter Control Register2 Update Busy

When Timer/Counter2 operates asynchronously and TCCR2A is written, this bit becomes set.

When TCCR2A has been updated from the temporary storage register, this bit is cleared by

hardware. A logical zero in this bit indicates that TCCR2A is ready to be updated with a new

value.

• Bit 0 – TCR2BUB: Timer/Counter Control Register2 Update Busy

When Timer/Counter2 operates asynchronously and TCCR2B is written, this bit becomes set.

When TCCR2B has been updated from the temporary storage register, this bit is cleared by

hardware. A logical zero in this bit indicates that TCCR2B is ready to be updated with a new

value.

If a write is performed to any of the five Timer/Counter2 Registers while its update busy flag is

set, the updated value might get corrupted and cause an unintentional interrupt to occur.

The mechanisms for reading TCNT2, OCR2A, OCR2B, TCCR2A and TCCR2B are different.

When reading TCNT2, the actual timer value is read. When reading OCR2A, OCR2B, TCCR2A

and TCCR2B the value in the temporary storage register is read.

Bit

–

EXCLK

AS2

TCN2UB

OCR2AUB

OCR2BUB

TCR2AUB

TCR2BUB

ASSR

Read/Write

R/W

Initial Value

ATmega88 Datasheet(PDF) 154 Page - ATMEL Corporation

ATmega88 Datasheet(HTML) 154 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL