ATmega88 datasheet(282/340 Pages) ATMEL

282 / 340 page

282

7530H–AVR–02/09

ATmega48/88/168 Automotive

25.2.1

Latching of Fuses

The fuse values are latched when the device enters programming mode and changes of the

fuse values will have no effect until the part leaves Programming mode. This does not apply to

the EESAVE Fuse which will take effect once it is programmed. The fuses are also latched on

Power-up in Normal mode.

25.3

Signature Bytes

All Atmel microcontrollers have a three-byte signature code which identifies the device. This

code can be read in both serial and parallel mode, also when the device is locked. The three

bytes reside in a separate address space.

25.3.1

ATmega48 Signature Bytes

0x000: 0x1E (indicates manufactured by Atmel).

0x001: 0x92 (indicates 4KB Flash memory).

0x002: 0x05 (indicates ATmega48 device when 0x001 is 0x92).

25.3.2

ATmega88 Signature Bytes

0x000: 0x1E (indicates manufactured by Atmel).

0x001: 0x93 (indicates 8KB Flash memory).

0x002: 0x0A (indicates ATmega88 device when 0x001 is 0x93).

25.3.3

ATmega168 Signature Bytes

0x000: 0x1E (indicates manufactured by Atmel).

0x001: 0x94 (indicates 16KB Flash memory).

0x002: 0x06 (indicates ATmega168 device when 0x001 is 0x94).

25.4

Calibration Byte

The ATmega48/88/168 has a byte calibration value for the internal RC Oscillator. This byte

resides in the high byte of address 0x000 in the signature address space. During reset, this byte

is automatically written into the OSCCAL Register to ensure correct frequency of the calibrated

RC Oscillator.

25.5

Parallel Programming Parameters, Pin Mapping, and Commands

This section describes how to parallel program and verify Flash Program memory, EEPROM

Data memory, Memory Lock bits, and Fuse bits in the ATmega48/88/168. Pulses are assumed

to be at least 250 ns unless otherwise noted.

25.5.1

Signal Names

In this section, some pins of the ATmega48/88/168 are referenced by signal names describing

their functionality during parallel programming, see Figure 25-1 and Table 25-8. Pins not

described in the following table are referenced by pin names.

The XA1/XA0 pins determine the action executed when the XTAL1 pin is given a positive pulse.

The bit coding is shown in Table 25-10.

When pulsing WR or OE, the command loaded determines the action executed. The different

Commands are shown in Table 25-11.

ATmega88 Datasheet(PDF) 282 Page - ATMEL Corporation

ATmega88 Datasheet(HTML) 282 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL