Electronic Components Datasheet Search
  English  ▼

X  

SC824 Datasheet(PDF) 20 Page - Semtech Corporation

Part # SC824
Description  Single-cell Li-Ion Charger Tri-Mode with Timer and NTC
PDF  29 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  SEMTECH [Semtech Corporation]
Direct Link  http://www.semtech.com
Logo SEMTECH - Semtech Corporation

SC824 Datasheet(HTML) 20 Page - Semtech Corporation

Back Button SC824 Datasheet HTML 16Page - Semtech Corporation SC824 Datasheet HTML 17Page - Semtech Corporation SC824 Datasheet HTML 18Page - Semtech Corporation SC824 Datasheet HTML 19Page - Semtech Corporation SC824 Datasheet HTML 20Page - Semtech Corporation SC824 Datasheet HTML 21Page - Semtech Corporation SC824 Datasheet HTML 22Page - Semtech Corporation SC824 Datasheet HTML 23Page - Semtech Corporation SC824 Datasheet HTML 24Page - Semtech Corporation Next Button
Zoom Inzoom in Zoom Outzoom out
 20 / 29 page
background image
SC824
20
When thermal limiting is inactive,
T
J
= T
A
+ V
Δ
I
FQ
θ
JA
,
where T
A
is the ambient temperature, V
Δ
is the voltage dif-
ference between the VIN pin and the BAT pin, I
FQ
is the
programmed fast charge current, and θ
JA
is the thermal
resistance from junction to ambient. However, if T
J
com-
puted this way exceeds T
TL
, then thermal limiting will
become active and the thermal limiting junction tempera-
ture will be
T
JTL
= T
A
+ V
Δ
I(T
JTL
) θ
JA
,
where
I(T
JTL
) = I
FQ
+ i
T
(T
JTL
− T
TL
).
(Note that i
T
is a negative quantity.) Combining these two
equations and solving for T
JTL
, the steady state junction
temperature during active thermal limiting is
JA
T
JA
TL
T
FQ
A
JTL
i
V
1
T
i
I
V
T
T
.
The thermal limiting controller is able to reduce output
current to zero. However, this does not happen in prac-
tice. Output current is reduced to I(T
JTL
), reducing power
dissipation such that die temperature equilibrium T
JTL
is
reached.
While thermal limiting is active, all charger functions
remain active and the charger logical state is preserved.
See the section Input Over-Voltage Protection for an
example of thermal limiting operation.
Operating a Charging Adapter in Current Limit
In high charging current applications, charger power dis-
sipation can be greatly reduced by operating the charging
adapter in current limit. The SC824 supports adapter-
current-limited charging with a low UVLO falling threshold
and with internal circuitry designed for low input voltage
operation. To operate an adapter in current limit, R
IPRGM
is
chosen such that the programmed fast-charge current I
FQ
exceeds the current limit of the charging adapter I
AD-LIM
.
The charging load will pull the adapter output voltage
(the VIN pin input voltage) down to the battery voltage
plus the charger dropout voltage. Power dissipation in
the SC824 will be reduced to the charger dropout voltage
multiplied by I
AD-LIM
.
If I
AD-LIM
is less than 20% of I
FQ
, then the adapter voltage can
be pulled down to the battery voltage while the battery
voltage is still below the precharge threshold. In this case,
ensure that the adapter will maintain its current limit
below 20% of I
FQ
at least until the battery voltage exceeds
the precharge threshold. Failure to do so could permit
charge current to exceed the precharge current while the
battery voltage is below the precharge threshold. This is
because the low input voltage can also compress the pre-
charge threshold internal reference voltage to below the
battery voltage. This will prematurely advance the charger
logic from precharge current regulation to fast-charge
regulation, and the charge current will be permitted, by
the charger, to exceed the safe level recommended for
pre-charge conditioning.
The low UVLO falling threshold (
VT
UVLO-F) permits the
adapter voltage to be pulled down to just above the
battery voltage only in adapter mode (MODE pin
grounded). In either USB mode, Under-Voltage Load
Regulation (UVLR) prevents the input being pulled down
by the charging current to below the UVLR limit of
V
UVLR
= 4.51V typically.
The SC824 should be operated with the adapter voltage
below the rising selection threshold (VT
UVLO-R
) only if the
low input voltage is the result of adapter current limiting.
This implies that the VIN pin voltage first exceeds
VT
UVLO-R
to begin charging and is subsequently pulled down by the
charging current to just above the battery voltage.
Interaction of Thermal Limiting and CLA Charging
To permit the charge current to be limited by the adapter,
it is necessary that the adapter mode fast-charge current
be programmed greater than the maximum adapter
current, (I
AD-LIM
). In this configuration, the CC regulator will
operate with its pass device fully on (in saturation, also
called “dropout”). The voltage drop from VIN to BAT is
determined by the R
DS-ON
of the internal pass device multi-
plied by the adapter current.
Applications Information (continued)



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com