| Electronic Components Datasheet Search |
|
SC824 Datasheet(PDF) 26 Page - Semtech Corporation |
|
|
|||||||||||||||||||||||||||||
SC824 Datasheet(HTML) 26 Page - Semtech Corporation |
|
26 / 29 page ![]() SC824 26 Applications Information (continued) parallel IPRGM resistor, while selecting high power mode (MODE pin driven high) for both low or high power USB charging. The external circuit is similar to that illustrated in Figure 7. For USB low power mode charging, the external transistor is turned off. For adapter mode or USB high power mode, the external transistor is turned on. The effect of the switched parallel IPRGM resistor is to reduce the effective programming resistance and thus raise the fast-charge current. A 300mAhr battery with maximum fast-charge current of 300mA is an example. The adapter mode and USB high power mode fast-charge currents should both be set to 300mA max. The USB input low power fast-charge current is 100mA max. Refer to the circuit in Figure 7 and the data of Figures 1a and 1b. For I FQ = 300mA max, R IPRGM = 7.50kΩ is desired. A fixed IPRGM resistor of R IPRGM = 23.2kΩ pro- grams I FQ = 100mA max for USB low power charging. When parallel resistor R IPRGM_HI = 11.0kΩ is switched in, the equivalent IPRGM resistor is 7.50kΩ, for I FQ = 300mA max. USB Low Power Mode Alternative Where a USB mode selection signal is not available, or for a low capacity battery where system cost or board space make USB low power mode external current program- ming impractical, USB low power charging can be sup- ported indirectly. The IPRGM pin resistance can be selected to obtain the desired USB high power charge current. Then, with the MODE pin always configured for USB high power mode, the UVLR feature will ensure that the charging load on the VIN pin will never pull the USB Vbus supply voltage below V UVLR regardless of the host or hub supply limit. The UVLR limit voltage guarantees that the voltage of the USB Vbus supply will not be loaded below the low power voltage specification limit, as seen by any other low power devices connected to the same USB host or hub. Under-voltage load regulation can also be beneficial for charging small batteries. Instead of switching the pro- gramming resistor depending on the USB mode, UVLR (while selecting USB high power mode) can permit charg- ing at whatever charge current a USB hub low-power supply can provide without compromising the integrity of the hub power supply for other devices. USB Dedicated Charger Compatibility The SC824 is especially well suited to the USB Charging Specification, Revision 1.0, Dedicated Charger, Sections 3.5 and 4.1. Important features that support compliance include low quiescent current when disabled (less than 1.5mA), and selectable current limited supply charging behavior. The USB Dedicated Charger is required to limit its output current to more than 0.5A and less than 1.5A. A dedicated charger identifies itself by shorting together the USB D+ and D- lines. Once the dedicated charger is detected, the SC824, with its 1A max programmed fast charge current in any mode, permits the fast-charge current to be set higher than the 500mA USB High Power Mode limit to permit faster charging of a large battery. (See the section Design Considerations — Large Battery.) Regardless of the SC824 programmed current, any speci- fication compliant USB Dedicated Charger will either supply more than the programmed fast charge current (and so will regulate to its specified output voltage), or will limit its output current such that its output voltage will be pulled down. The USB Dedicated Charger is required to maintain its current limit down to 2V. By selecting Adapter Mode, the SC824 input will be pulled down to the battery voltage plus charging path dropout. This behavior is rec- ognized in the USB Battery Charging Specification, Section 3.5, as an accepted means to reduce power dissipation in the device while charging at high current. If there are additional system circuits requiring that the USB Vbus node voltage be maintained above the USB Low Power Mode minimum voltage specification (4.4V), the SC824 USB High Power Mode should be selected. This mode enables Under-Voltage Load Regulation, which will regulate the charging output current, if necessary, to match the Dedicated Charger current limit while main- taining V UVLR (nominally 4.51V) at the VIN pin. Either of these SC824 charging modes will ensure reliable charging at any programmed charge current, using any USB Battery Charging Specification compliant Dedicated Charger, regardless of its current limit. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |