6

・All specifications are subject to change without notice.

SWS1000L Specifications

(*1) (

): Peak output current is possible at 170-265VAC input range, operating period at peak output current is less than 10sec, duty less than 35%.

Average output power and current is less than maximum output power and maximum output current.

(*2) At maximum output power, nominal input voltage, Ta=25°C.

(*3) For cases where conformance to various safety specs (UL, CSA, EN) are required, to be described as 100-240VAC, 50/60Hz on name plate.

(*4) First/second inrush current, not applicable for the in-rush current to noise filter for less than 0.2ms.

(*5) Ripple & noise are measured at 20MHz by using a 150mm twisted pair of load wires terminated with a 0.1uF film capacitor and a 47uF

electrolytic capacitor.

(*6) Measure line & load regulation at output terminal M4 tapped point.

(*7) 85-265VAC, constant load.

(*8) No load - full load (maximum power), constant input voltage.

(*9) Constant current limit with automatic recovery.

Avoid to operate at overload or dead short for more than 30 seconds.

(*10) OVP circuit will shutdown output, manual reset (remote ON/OFF control reset or re-power on).

(*11) Measured by each measuring method of UL, CSA, EN and DENAN (at 60Hz), Ta=25°C.

Worst case: <0.3mA at 264VAC, 63Hz (normal condition); <0.5mA (single fault condition)

(*12) Refer to output derating curve for details of output derating versus ambient temperature.

- Load (%) is percent of maximum output power and maximum output current (Item 2 and 3).

Do not exceed derating of maximum output power and maximum output current.

- 100% load start up at -40°C is possible. However, it may not fulfil all the specifications.

(*13) Category 4 exposure levels: Trunk transportation over U.S. highways, composite two-wheeled trailer.

(*14) As for DENAN, designed to meet at 100VAC.

ITEMS/UNITS

MODEL SWS1000L-3 SWS1000L-5 SWS1000L-12 SWS1000L-15 SWS1000L-24 SWS1000L-36 SWS1000L-48 SWS1000L-60

Input

Voltage Range

(*3)

V

AC85-265 or DC120-350

Frequency

(*3)

Hz

47-63

Power Factor (115/230VAC) (typ) (*2)

0.98 / 0.95

Efficiency (115/230VAC) (typ) (*2)

×

75 / 77

79 / 81

82 / 84

84 / 86

Current (115/230VAC) (typ) (*2)

A

8 / 4

12 / 6

Inrush Current (typ)

(*4)

A

20A/40A at 115VAC, 40A/40A at 230VAC, Ta=25°C (first inrush/second inrush)

Leakage Current (typ)

(*11)

mA

0.1mA at 115VAC, 60Hz / 0.2mA at 230VAC, 60Hz

Output

Nominal Voltage

VDC

3.3

5

12

15

24

36

48

60

Maximum Current (Peak Current) (*1)

A

200

88

70

44 (51)

29

22 (25)

17

Maximum Power (Peak Power) (*1)

W

660

1000

1056

1050

1056 (1224)

1044

1056 (1200)

1020

Maximum Line Regulation (*6)(*7)

mV

20

48

60

96

144

192

240

Maximum Load Regulation (*6)(*8)

mV

30

72

90

144

216

288

360

Temperature Coefficient

Less than 0.02%/°C

Maximum Ripple & Noise (115/230VAC) (0

≤Ta≤74°C) (*5) mVp-p

120

150

200

Maximum Ripple & Noise (115/230VAC) (-20

≤Ta<0°C) (*5) mVp-p

160

180

240

Hold-up Time (115/230VAC) (typ) (*2)

ms

20

Voltage Adjustable Range

VDC 2.64-3.96

4.0-6.0

9.6-14.4

12.0-19.5 19.2-28.8 28.8-43.2 38.4-56.0 48.0-66.0

Function

Over Current Protection

(*9)

A

>210

>92.4

>73.5

>51.6

>30.5

>25.3

>17.9

Over Voltage Protection (*10) VDC 4.12-5.61 6.25-7.25 15.0-17.4 20.2-23.4 30.0-34.8 45.0-52.2 58.5-68.2 69.0-81.0

Remote Sensing

Possible

Remote ON/OFF Control

Possible

Parallel Operation

Possible

Series Operation

Possible

Monitoring Signal

ALM ( Open Collector Output )

Line DIP

Designed to meet SEMI-F47 (200VAC line only)

Environment

Operating Temperature (*12)

×

-20 to +74 °C (-20°C to +50°C: 100%, +74°C: 50%), 100% load start up at -40°C

Storage Temperature

×

-40 to +85°C

Operating Humidity

×RH

20-90 (No dewdrop)

Storage Humidity

×RH

10-95 (No dewdrop)

Vibration

(*13)

Designed to meet MIL-STD-810F 514.5 Category 4, 10

Shock (In package)

Designed to meet MIL-STD-810F 516.5 Procedure I,VI

Cooling

Forced air by build-in fan

Isolation

Withstand Voltage

Input - Output : 4.0kVAC (20mA), Input - FG : 2.0kVAC (20mA) Output - FG : 500VAC (100mA)

(60V model: 651VAC(130mA)), Output - CNT/ALM/AUX : 100VAC (100mA) for 1min.

Isolation Resistance

Input - FG, Input - Output and Output - FG: More than 50M

Ω (500VDC),

Output - CNT/ALM/AUX: More than 50M

Ω (100VDC) at Ta=25°C and 70%RH

Standards

Safety Standards

(*14)

Approved by UL60950-1, CSA60950-1, EN60950-1, EN50178, UL60601-1, EN60601-1,

CSA-C22.2 No.601.1-M90 Designed to meet DENAN, EN61010-1.

PFHC

Designed to meet IEC61000-3-2

EMI

Designed to meet VCCI-B, FCC-B, EN55011/EN55022-B

Immunity

Designed to meet EN61000-4-2 (Level 2,3), -3 (Level 3), -4 (Level 3), -5 (Level 3,4), -6 (Level 3), -8 (Level 4), -11

Mechanical

Weight (typ)

g

2.3kg

Size (W×H×D)

mm

150 x 61 x 240 (Refer to Outline Drawing)

A

47μ

0.1μ

+

+Ｖ

150ｍｍ

-Ｖ

Fig.A

Measurement point for Ripple and Noise.

Measurement point for Vo Line/Load Regulation.