ADSP-BF607 datasheet(14/44 Pages) AD

14 / 44 page

Rev. PrD

Page 14 of 44

March 2012

ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data

The CAN controller offers the following features:

• 32 mailboxes (8 receive only, 8 transmit only, 16 configu-

rable for receive or transmit).

• Dedicated acceptance masks for each mailbox.

• Additional data filtering on first two bytes.

• Support for both the standard (11-bit) and extended (29-

bit) identifier (ID) message formats.

• Support for remote frames.

• Active or passive network support.

• CAN wakeup from hibernation mode (lowest static power

consumption mode).

• Interrupts, including: TX complete, RX complete, error

and global.

An additional crystal is not required to supply the CAN clock, as

the CAN clock is derived from a system clock through a pro-

grammable divider.

10/100 Ethernet MAC

The processor can directly connect to a network by way of an

embedded fast Ethernet media access controller (MAC) that

supports both 10-BaseT (10M bits/sec) and 100-BaseT (100M

bits/sec) operation. The 10/100 Ethernet MAC peripheral on the

processor is fully compliant to the IEEE 802.3-2002 standard

and it provides programmable features designed to minimize

supervision, bus use, or message processing by the rest of the

processor system.

Some standard features are:

• Support and RMII protocols for external PHYs

• Full duplex and half duplex modes

• Media access management (in half-duplex operation)

• Flow control

• Station management: generation of MDC/MDIO frames

for read-write access to PHY registers

Some advanced features are:

• Automatic checksum computation of IP header and IP

payload fields of Rx frames

• Independent 32-bit descriptor-driven receive and transmit

DMA channels

• Frame status delivery to memory through DMA, including

frame completion semaphores for efficient buffer queue

management in software

• Tx DMA support for separate descriptors for MAC header

and payload to eliminate buffer copy operations

• Convenient frame alignment modes

• 47 MAC management statistics counters with selectable

clear-on-read behavior and programmable interrupts on

half maximum value

• Advanced power management

• Magic packet detection and wakeup frame filtering

• Support for 802.3Q tagged VLAN frames

• Programmable MDC clock rate and preamble suppression

IEEE 1588 Support

The IEEE 1588 standard is a precision clock synchronization

protocol for networked measurement and control systems. The

processor includes hardware support for IEEE 1588 with an

integrated precision time protocol synchronization engine

(PTP_TSYNC). This engine provides hardware assisted time

stamping to improve the accuracy of clock synchronization

between PTP nodes. The main features of the engine are:

• Support for both IEEE 1588-2002 and IEEE 1588-2008 pro-

tocol standards

• Hardware assisted time stamping capable of up to 12.5 ns

resolution

• Lock adjustment

• Automatic detection of IPv4 and IPv6 packets, as well as

PTP messages

• Multiple input clock sources (SCLK0, RMII clock, external

clock)

• Programmable pulse per second (PPS) output

• Auxiliary snapshot to time stamp external events

USB 2.0 On-the-Go Dual-Role Device Controller

The USB 2.0 OTG dual-role device controller provides a low-

cost connectivity solution for the growing adoption of this bus

standard in industrial applications, as well as consumer mobile

devices such as cell phones, digital still cameras, and MP3 play-

ers. The USB 2.0 controller allows these devices to transfer data

using a point-to-point USB connection without the need for a

PC host. The module can operate in a traditional USB periph-

eral-only mode as well as the host mode presented in the On-

the-Go (OTG) supplement to the USB 2.0 specification.

The USB clock (USB_CLKIN) is provided through a dedicated

external crystal or crystal oscillator.

The USB On-the-Go dual-role device controller includes a

Phase Locked Loop with programmable multipliers to generate

the necessary internal clocking frequency for USB.

POWER AND CLOCK MANAGEMENT

The processor provides four operating modes, each with a dif-

ferent performance/power profile. When configured for a 0 volt

internal supply voltage (VDD_INT), the processor enters the hiber-

nate state. Control of clocking to each of the processor

peripherals also reduces power consumption. See Table 5 for a

summary of the power settings for each mode.

Crystal Oscillator (SYS_XTAL)

The processor can be clocked by an external crystal, (Figure 6) a

sine wave input, or a buffered, shaped clock derived from an

external clock oscillator. If an external clock is used, it should be

a TTL compatible signal and must not be halted, changed, or

operated below the specified frequency during normal opera-

tion. This signal is connected to the processor’s SYS_CLKIN

ADSP-BF607 Datasheet(PDF) 14 Page - Analog Devices

ADSP-BF607 Datasheet(HTML) 14 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

Datasheet Download

Link URL