| Electronic Components Datasheet Search |
|
LT1672 Datasheet(PDF) 12 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LT1672 Datasheet(HTML) 12 Page - Linear Technology |
|
12 / 22 page ![]() LTC3108 12 3108fb Introduction The LTC3108 is designed to gather energy from very low input voltage sources and convert it to usable output volt- ages to power microprocessors, wireless transmitters and analog sensors. Such applications typically require much more peak power, and at higher voltages, than the input voltage source can produce. The LTC3108 is designed to accumulate and manage energy over a long period of time to enable short power bursts for acquiring and transmit- ting data. The bursts must occur at a low enough duty cycle such that the total output energy during the burst does not exceed the average source power integrated over the accumulation time between bursts. For many applications, this time between bursts could be seconds, minutes or hours. The PGD signal can be used to enable a sleeping micro- processor or other circuitry when VOUT reaches regulation, indicating that enough energy is available for a burst. Input Voltage Sources The LTC3108 can operate from a number of low input voltage sources, such as Peltier cells, photovoltaic cells or thermopile generators. The minimum input voltage required for a given application will depend on the transformer turns ratio, the load power required, and the internal DC resistance (ESR) of the voltage source. Lower ESR will allow the use of lower input voltages, and provide higher output power capability. APPLICATIONS INFORMATION Figure 2. Typical Performance of a Peltier Cell Acting as a Thermoelectric Generator Refer to the IIN vs VIN curves in the Typical Performance Characteristics section to see what input current is required from the source for a given input voltage. For a given transformer turns ratio, there is a maximum recommended input voltage to avoid excessively high secondary voltages and power dissipation in the shunt regulator. It is recommended that the maximum input voltage times the turns ratio be less than 50. Note that a low ESR bulk decoupling capacitor will usually be required across the input source to prevent large voltage droop and ripple caused by the source’s ESR and the peak primary switching current (which can reach hundreds of milliamps). The time constant of the filter capacitor and the ESR of the voltage source should be much longer than the period of the resonant switching frequency. Peltier Cell (Thermoelectric Generator) A Peltier cell (also known as a thermoelectric cooler) is made up of a large number of series-connected P-N junc- tions, sandwiched between two parallel ceramic plates. Although Peltier cells are often used as coolers by apply- ing a DC voltage to their inputs, they will also generate a DC output voltage, using the Seebeck effect, when the two plates are at different temperatures. The polarity of the output voltage will depend on the polarity of the tem- perature differential between the plates. The magnitude of the output voltage is proportional to the magnitude of the temperature differential between the plates. When used in 3108 F02 1000 100 10 1 1 10 100 dT (°C) 1 100 10 0.1 VOC MAX POUT (IDEAL) TEG: 30mm 127 COUPLES R = 2Ω |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |