Electronic Components Datasheet Search
  English  ▼

X  

AD14160KB-4 Datasheet(PDF) 12 Page - Analog Devices

Part # AD14160KB-4
Description  Quad-SHARC DSP Multiprocessor Family
PDF  52 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

AD14160KB-4 Datasheet(HTML) 12 Page - Analog Devices

Back Button AD14160KB-4 Datasheet HTML 8Page - Analog Devices AD14160KB-4 Datasheet HTML 9Page - Analog Devices AD14160KB-4 Datasheet HTML 10Page - Analog Devices AD14160KB-4 Datasheet HTML 11Page - Analog Devices AD14160KB-4 Datasheet HTML 12Page - Analog Devices AD14160KB-4 Datasheet HTML 13Page - Analog Devices AD14160KB-4 Datasheet HTML 14Page - Analog Devices AD14160KB-4 Datasheet HTML 15Page - Analog Devices AD14160KB-4 Datasheet HTML 16Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 12 / 52 page
background image
AD14160/AD14160L
–12–
REV. A
TARGET BOARD CONNECTOR FOR EZ-ICE PROBE
The ADSP-2106x EZ-ICE Emulator uses the IEEE 1149.1
JTAG test access port of the ADSP-2106x to monitor and con-
trol the target board processor during emulation. The EZ-ICE
probe requires that the AD14160/AD14160L’s CLKIN (op-
tional), TMS, TCK,
TRST, TDI, TDO, EMU and GND signals
be made accessible on the target system via a 14-pin connector
(a pin strip header) such as that shown in Figure 6. The EZ-
ICE probe plugs directly onto this connector for chip-on-board
emulation. You must add this connector to your target board
design if you intend to use the ADSP-2106x EZ-ICE. The
length of the traces between the connector and the AD14160/
AD14160L’s JTAG pins should be as short as possible.
TOP VIEW
13
14
11
12
910
9
78
56
34
12
EMU
CLKIN (OPTIONAL)
TMS
TCK
TRST
TDI
TDO
GND
KEY (NO PIN)
BTMS
BTCK
BTRST
BTDI
GND
Figure 6. Target Board Connector for ADSP-2106x EZ-ICE
Emulator (Jumpers in Place)
The 14-pin, 2-row pin strip header is keyed at the Pin 3 location;
Pin 3 must be removed from the header. The pins must be
0.025 inch square and at least 0.20 inch in length. Pin spacing
should be 0.1
× 0.1 inches. Pin strip headers are available from
vendors such as 3M, McKenzie and Samtec.
The BTMS, BTCK,
BTRST and BTDI signals are provided so
that the test access port can also be used for board-level testing.
When the connector is not being used for emulation, place
jumpers between the Bxxx pins and the xxx pins as shown in
Figure 6. If you are not going to use the test access port for
board testing, tie
BTRST to GND and tie or pull up BTCK to
VDD. The TRST pin must be asserted after power-up (through
BTRST on the connector) or held low for proper operation of
the AD14160/AD14160L. None of the Bxxx pins (Pins 5, 7, 9,
11) are connected on the EZ-ICE probe.
The JTAG signals are terminated on the EZ-ICE probe as follows:
Signal
Termination
TMS
Driven through 22
Ω Resistor (16 mA/3.2 mA Driver)
TCK
Driven at 10 MHz through 22
Ω Resistor (16 mA/
3.2 mA Driver)
TRST
Driven by Open-Drain Driver* (Pulled Up by On-Chip
20 k
Ω Resistor)
TDI
Driven by 16 mA/3.2 mA Driver
TDO
One TTL Load, No Termination
CLKIN
One TTL Load, No Termination (Optional Signal)
EMU
4.7 k
Ω Pull-Up Resistor, One TTL Load (Open-Drain
Output from ADSP-2106x)
*
TRST is driven low until the EZ-ICE probe is turned on by the EZ-ICE
software (after the invocation command).
Figure 7 shows JTAG scan path connections for the multi-
processor system.
SHARC_A
TDI
TDO
EZ-ICE
JTAG
CONNECTOR
TDI
TCK
TMS
EMU
TRST
TDO
CLKIN
OTHER
JTAG
CONTROLLER
SHARC_B
TDI
TDO
SHARC_C
TDI
TDO
SHARC_D
TDI
TDO
JTAG DEVICE
(OPTIONAL)
TDI
TDO
TDI
TDO
ADSP-2106x
#n
OPTIONAL
Figure 7. JTAG Scan Path Connections for the AD14160/AD14160L



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com