STM32F407IG datasheet(87/167 Pages) STMICROELECTRONICS

87 / 167 page

STM32F405xx, STM32F407xx

Electrical characteristics

Doc ID 022152 Rev 2

87/167

Note:

For CL1 and CL2 it is recommended to use high-quality external ceramic capacitors in the

5 pF to 15 pF range selected to match the requirements of the crystal or resonator (see

Figure 30). CL1 and CL2, are usually the same size. The crystal manufacturer typically

specifies a load capacitance which is the series combination of CL1 and CL2.

Load capacitance CL has the following formula: CL = CL1 x CL2 / (CL1 + CL2) + Cstray where

Cstray is the pin capacitance and board or trace PCB-related capacitance. Typically, it is

between 2 pF and 7 pF.

Caution:

To avoid exceeding the maximum value of CL1 and CL2 (15 pF) it is strongly recommended

to use a resonator with a load capacitance CL ≤ 7 pF. Never use a resonator with a load

capacitance of 12.5 pF.

Example: if you choose a resonator with a load capacitance of CL = 6 pF, and Cstray = 2 pF,

then CL1 = CL2 = 8 pF.

Figure 30.

Typical application with a 32.768 kHz crystal

Table 29.

LSE oscillator characteristics (fLSE = 32.768 kHz)

(1)(2)

Based on characterization, not tested in production.

TBD stands for “to be defined”.

Symbol

Parameter

Conditions

Min

Typ

Max

Unit

Feedback resistor

TBD

C(3)

Refer to the note and caution paragraphs below the table, and to the application note AN2867 “Oscillator

design guide for ST microcontrollers”.

Recommended load capacitance

versus equivalent serial

resistance of the crystal (RS)

(4)

The oscillator selection can be optimized in terms of supply current using an high quality resonator with

small RS value for example MSIV-TIN32.768kHz. Refer to crystal manufacturer for more details

RS = 30 kΩ

TBD

LSE driving current

VDD = 3.3 V, VIN = VSS

TBD

µA

Oscillator Transconductance

TBD

µA/V

tSU(LSE)

(5)

tSU(LSE) is the startup time measured from the moment it is enabled (by software) to a stabilized

32.768 kHz oscillation is reached. This value is measured for a standard crystal resonator and it can vary

significantly with the crystal manufacturer

startup time

VDD is stabilized

TBD

ai17531

OSC32_OU T

OSC32_IN

fLSE

CL1

STM32F

32.768 kH z

resonator

Resonator with

integrated capacitors

Bias

controlled

gain

CL2

STM32F407IG Datasheet(PDF) 87 Page - STMicroelectronics

STM32F407IG Datasheet(HTML) 87 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL