CS4954 datasheet(14/56 Pages) CIRRUS

14 / 56 page

CS4954 CS4955

DS278PP4

4.12. Teletext Services

The CS4954/5 encodes the most common teletext

formats, such as European Teletext, World Stan-

dard Teletext (PAL and NTSC), and North Ameri-

can Teletext (NABTS).

Teletext data can be inserted in any of the TV lines

(blanking lines as well as active lines). In addition

the blanking lines can be individually allocated for

Teletext instantiation.

The input timing for teletext data is user program-

mable. See the section Teletext Services for further

details.

Teletext data can be independently inserted on ei-

ther one or all of the CVBS_1, CVBS_2, or S-video

signals.

4.13. Wide-Screen Signaling Support and

CGMS

Insertion of wide-screen signal encoding for PAL

and NTSC standards is supported and CGMS

(Copy Generation Management System) for NTSC

in Japan. Wide-screen signals are inserted in lines

23 and 336 for PAL, and lines 20 and 283 for

NTSC.

4.14. VBI Encoding

This chip supports the transmission of control sig-

nals in the vertical blanking time interval according

to SMPTE RP 188 recommendations. VBI encoded

data can be independently inserted into either or all

of CVBS_1, CVBS_2 or S-video signals.

4.15. Control Registers

The control and configuration of the CS4954/5 is

accomplished primarily through the control regis-

ter block. All of the control registers are uniquely

addressable via the internal address register. The

control register bits are initialized during device

RESET.

See the Programming section of this data sheet for

the individual register bit allocations, bit operation-

al descriptions, and initialization states.

4.16. Testability

The digital circuits are completely scanned by an

internal scan chain, thus providing close to 100%

fault coverage.

OPERATIONAL DESCRIPTION

5.1.

Reset Hierarchy

The CS4954/5 is equipped with an active low asyn-

chronous reset input pin, RESET. RESET is used to

initialize the internal registers and the internal state

machines for subsequent default operation. See the

electrical and timing specification section of this

data sheet for specific CS4954/5 device RESET

and power-on signal timing requirements and re-

strictions.

While the RESET pin is held low, the host interface

in the CS4954/5 is disabled and will not respond to

host-initiated bus cycles. All outputs are valid after

a time period following RESET pin low.

A device RESET initializes the CS4954/5 internal

registers to their default values as described by Ta-

ble 9, Control Registers. In the default state, the

CS4954/5 video DACs are disabled and the device

is internally configured to provide blue field video

data to the DACs (any input data present on the

V [7:0] pins is ignored at this time). Otherwise, the

CS4954/5 registers are configured for NTSC-M

ITU R.BT601 output operation. At a minimum, the

DAC Registers (0x04 and 0x05) must be written (to

enable the DACs) and the IN_MODE bit of the

CONTROL_0 Register (0x01) must be set (to en-

able ITU R.BT601 data input on V [7:0]) for the

CS4954/5 to become operational after RESET.

CS4954 Datasheet(PDF) 14 Page - Cirrus Logic

CS4954 Datasheet(HTML) 14 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

Datasheet Download

Link URL