| Electronic Components Datasheet Search |
|
MA7001 Datasheet(PDF) 6 Page - Dynex Semiconductor |
|
|
|||||||||||||||||||||||||||||
MA7001 Datasheet(HTML) 6 Page - Dynex Semiconductor |
|
6 / 15 page ![]() MA7001 6/15 SIGNAL DESCRIPTIONS Reset (RS) Reset occurs when RS is in a low state, setting both read and write pointers to the first location in memory. Reset is required prior to the first write. Both READ ( R) and WRITE (W) signals must be in high states during reset. Read Enable ( R): Providing the EMPTY FLAG ( EF) is not set, i.e. there is still data to be read, a read cycle commences on the falling edge of R, (see Figure 16). Data is read in a First-ln First-Out manner independent of write operations. When reads are disabled data outputs (Q0 - Q8) are in a high impedance state. Reading the last available memory location sets the EMPTY FLAG ( EF), which is cleared following a write cycle. Write Enable ( W): Providing the FULL FLAG ( FF) is not set, i.e. there exists at least one memory location for writing, a write cycle commences on the falling edge of ( W), (see Figure 17). Data is written into consecutive memory locations independent of read operations on the rising edge of W. Data set up and hold times are with respect to the rising edge of W. Expansion In ( Xl): There are two possible modes of operation for the FIFO. One with Xl grounded in which the device is in singledevice mode, the other is a depth expension mode or daisy chain configuration. In the latter mode Xl inputs come from EXPANSION OUT ( XO) outputs of the device preceding it in the chain. Expansion Out ( XO): In depth expansion mode XO from one device signals the next device in the chain that the last location in its memory has been accessed. Full Flag ( FF): FF becomes active when the last available memory location has been written to, (see Figure 18). In general, this occurs whenever the write pointer coincides with the read pointer following a write cycle. Writes are inhibited while FF is active, and may only proceed after a read cycle has occured. FF will go high tRFF after completion of a valid READ operation. FF will go low tWFF from the beginning of a subsequent WRITE operation, provided that a second READ has not been completed. Writes beginning tFFW after FF goes high, are valid. Writes beginning after FF goes low and ending more than tWPI before FF goes high, are invalid (ignored). Writes beginning less than twpl before FF goes high and less than tFFW later, may or may not occur (be valid) depending on the internal flag status (see Figure 19). If a Write to the last but one physical location completes while the last location (511th) is being Read, the FF will not be activated. The next Read should start after the last Write has completed. As a WRITE operation is being performed to the last physical memory location (511th) whilst the READ pointer is waiting at the 510th physical location the FULL flag is activated for a duration less than 20ns. Note: The last physical location (511th) is accessed after 511 WRITE or READ operations after RESET. Empty Flag ( EF): Following an initial RESET EF is active, becoming inactive after the first write cycle, (see Figure 20). EF becomes active once the read and write pointers are coincident following a read cycle. Reading will not take place whilst EF is active, and may only proceed once a write cycle has occured. EF will go high tWEF after completion of a valid WRITE operation. EF will again go low tREF from the beginning of a subsequent READ operation, provided that a second WRITE has not been completed. Reads beginning tEFR after EF goes high, are valid. Reads begun after EF goes low and ending more than tRPI before EF goes high, are invalid (ignored). Reads beginning less than tRIP before EF goes high and less than tEFR later, may or may not occur (be valid) depending on the internal flag status (See Figure 21). If a Read to the last but one physical location completes while the last location (511th) is being written, the EF will not be activated. The next Read should be activated after the last Write has completed. First Load/Retransmit ( FL/RT): This is a dual purpose input depending on the mode of operation of the device. In single device mode Xl = 0 data may be retransmitted, i.e. it may be re-read. In depth expansion mode FL signifies the first device in the chain. When RT is pulsed low the read pointer is set to the first memory location. The write pointer is unaffected. This feature is disabled in depth expansion mode, and can only be applied when R and W are inactive (See Figure 22). Data Inputs (D0 - D8): Data inputs, 9 bit word, for write operations. Data Outputs (Q0 - Q8): Data outputs, 9 bit word, for read operations. When R is inactive these outputs are in a high impedance state. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |