AT90PWM2 datasheet(191/365 Pages) ATMEL

191 / 365 page

191

4317K–AVR–03/2013

AT90PWM2/3/2B/3B

that there are no unread data in the receive buffer. Note that the TXC flag must be cleared

before each transmission (before UDR is written) if it is used for this purpose.

The following simple USART initialization code examples show one assembly and one C func-

tion that are equal in functionality. The examples assume asynchronous operation using polling

(no interrupts enabled) and a fixed frame format. The baud rate is given as a function parameter.

For the assembly code, the baud rate parameter is assumed to be stored in the r17:r16

Registers.

Note:

1. The example code assumes that the part specific header file is included.

For I/O Registers located in extended I/O map, “IN”, “OUT”, “SBIS”, “SBIC”, “CBI”, and “SBI”

instructions must be replaced with instructions that allow access to extended I/O. Typically

“LDS” and “STS” combined with “SBRS”, “SBRC”, “SBR”, and “CBR”.

More advanced initialization routines can be made that include frame format as parameters, dis-

able interrupts and so on. However, many applications use a fixed setting of the baud and

control registers, and for these types of applications the initialization code can be placed directly

in the main routine, or be combined with initialization code for other I/O modules.

18.6

Data Transmission – USART Transmitter

The USART Transmitter is enabled by setting the Transmit Enable (TXEN) bit in the UCSRB

den by the USART and given the function as the Transmitter’s serial output. The baud rate,

mode of operation and frame format must be set up once before doing any transmissions. If syn-

TABLE 2.

Assembly Code Example(1)

USART_Init:

; Set baud rate

sts

UBRRH, r17

sts

UBRRL, r16

; Set frame format: 8data, no parity & 2 stop bits

ldi

r16, (0<<UMSEL)|(0<<UPM0)|(1<<USBS)|(3<<UCSZ0)

sts

UCSRC,r16

; Enable receiver and transmitter

ldi

r16, (1<<RXEN0)|(1<<TXEN0)

sts

UCSRB,r16

ret

C Code Example

(1)

void

USART_Init( unsigned int baud )

{

/* Set baud rate */

UBRRH = (unsigned char)(baud>>8);

UBRRL = (unsigned char)baud;

/* Set frame format: 8data, no parity & 2 stop bits */

UCSRC = (0<<UMSEL)|(0<<UPM0)|(1<<USBS)|(3<<UCSZ0);

/* Enable receiver and transmitter */

UCSRB = (1<<RXEN0)|(1<<TXEN0);

}

AT90PWM2 Datasheet(PDF) 191 Page - ATMEL Corporation

AT90PWM2 Datasheet(HTML) 191 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL